INS0039 EN
SEP 2019
Rev. D
UltraSnap™ Surface ATP Test
For use with Hygiena™ ATP Monitoring Systems
Part No: US2020 (100 tests)
Description/ Intended Use:
UltraSnap Surface ATP Test is a self-contained device for
use with Hygiena luminometers. The test device and
luminometer create a system used for monitoring hygienic
status of surfaces on processing equipment and other
environments in a wide range of industries. The system
works by measuring adenosine triphosphate (ATP), the
universal energy molecule found in all animal, plant,
bacterial, yeast, and mold cells. Product residues from
organic matter left on surfaces contain ATP. Microbial
contamination on a surface contains ATP but typically in
smaller amounts. After proper cleaning, all sources of ATP
should be significantly reduced. When a sample is collected
and ATP is brought into contact with the unique liquid
stable Luciferase/ Luciferin reagent in the UltraSnap test
device, light is emitted in direct proportion to the amount of
ATP present in the sample. The luminometer measures
generated light and reports results in Relative Light Units
(RLU). RLU result provides information on the level of
contamination within seconds. The higher the RLU number,
the more ATP present, and the dirtier the surface. It is
important to note that UltraSnap is designed to detect
invisible/trace amounts of residue. Overloading the swab
with physical matter by swabbing a visibly dirty surface will
inhibit the bioluminescent reaction and produce inaccurate
results.
For water samples such as Clean In Place (CIP) rinse water
testing, use AquaSnap™ Water ATP Test Devices. Visit
for more information.
Directions:
Instructional Video:
Before beginning testing, turn on luminometer. If
luminometer has been programmed with test locations,
select appropriate location before running test.
1.
Allow UltraSnap to equilibrate to room temperature
(21 – 25 °C) before use. Holding swab tube firmly,
twist and pull top of swab out of swab tube.
Condensation may be visible on inside of swab tube;
this is normal.
2.
Thoroughly swab a standard 10 x 10 cm (4 x 4 inches)
area for a typical flat surface. Swab tip is pre-
moistened for maximum sample collection. For
irregular surfaces, ensure swabbing technique
remains consistent for each test and swab a large
enough area to collect a representative sample.
Important swabbing technique tips:
•
Do not touch swab or inside of sample device
with fingers.
•
Rotate swab while collecting sample to maximize
sample collection on swab tip.
•
Apply sufficient pressure to create flex in swab
shaft.
•
Swab in a crisscross pattern vertically,
horizontally, and in both diagonal directions.
•
Refer to instructional video for demonstration:
3.
After swabbing, replace swab back in swab tube.
4.
To activate device, hold swab tube firmly and use
thumb and forefinger to break Snap-Valve by bending
bulb forward and backward. Squeeze bulb twice,
expelling all liquid down swab shaft.
5.
Bathe swab bud in liquid by shaking
for 5 – 10
seconds. Once activated, sample must be read in
luminometer within 30 seconds.
6.
Holding luminometer upright, insert entire UltraSnap
device into Hygiena luminometer.
7.
A.
If using the EnSURE™ Touch, close lid and press
“Run Test” to initiate measurement. Refer to the
instrument manual for operating instructions. Results
will be displayed in 10 seconds.
B.
If using the EnSURE™ or SystemSURE Plus,
close lid and press "OK" to initiate the measurement.
Refer to the instrument manual for operating
instructions. Results will be displayed in 15 seconds.
Interpretation of Results:
Hygiena luminometers are preset with Pass & Fail RLU
limits of of 20 and 60 RLU for the EnSURE Touch and 10
and 30 for the EnSURE and SystemSURE Plus. These
limits are based on industry standards and published
study recommendations. When using default settings,
readings less than 20 on the EnSURE Touch (10 on
EnSURE and SystemSURE Plus) RLU indicate surface is
considered clean. Readings between 21-59 on the
EnSURE Touch (11-29 on EnSURE and SystemSURE
Plus) RLU indicate a warning, surface is not adequately
clean. If reading is greater than 60 on the EnSURE Touch
(30 on EnSURE and SystemSURE Plus) RLU, surface is
considered dirty. Hygiena recommends setting RLU
thresholds according to standards of your facility. Visit
to view recommended practices or call
our technical representatives for guidance.
Calibration Control:
It is advisable to run positive and negative controls
according to Good Laboratory Practices. Hygiena offers the
following controls:
•
(Part # PCD4000) Calibration Control Kit for Hygiena
Luminometers
•
(Part # CK25) ATP Positive Control Kit for ATP Test
Devices
•
(Part # CAL) CalCheck LED Calibration Verification
Device
Storage & Shelf Life:
•
Store at 2 – 8 °C (36 – 46 °F)
•
Test devices will tolerate temperature abuse for 4
weeks at room temperature (< 25 °C)
•
Store UltraSnap devices out of direct sunlight.
•
Devices have a 15-month shelf life. Refer to
expiration date on label.
Disposal:
UltraSnap devices are made of 100% recyclable plastic
and may be discarded accordingly.
Safety & Precautions:
Components of UltraSnap do not pose any health risk
when used in accordance with standard laboratory
practice and procedures of this insert.
•
UltraSnap test devices are for one-time use. Do not
reuse.
For further safety instruction, refer to Safety Data Sheet
(SDS).
Hygiena Liability:
Hygiena will not be liable to user or others for any loss or
damage whether direct or indirect, incidental or
consequential from use of this device. If this product is
proven to be defective, Hygiena’s sole obligation will be to
replace product or at its discretion, refund the purchase
price. Promptly notify Hygiena within 5 days of discovery
of any suspected defect and return product to Hygiena.
Please contact Customer Service for a Returned Goods
authorization number.
Contact Information:
If more information is required, please visit us at
www.hygiena.com
or contact us at:
Hygiena - Americas
Phone: +1 805.388.8007
Email:
Hygiena - International
Phone: +44 (0)1923 818821
Email:
