MAINTENANCE
-
CLEANING
1)
Remove the detector from its base.
2)
Smoke entry areas and thermistor area: use a small,
soft bristle brush to dislodge any obvious contaminants
such as insects, spider webs, hairs, etc.
3)
Smoke entry areas and thermistor area: use a small
vacuum tube or dry, clean, compressed air to suck up or
blow any remaining small particles away.
4)
Wipe the exterior housing of the detector with a clean,
damp, lint
-
free cloth to remove any surface film that can
later attract airborne contaminants.
5)
Install the detector onto its base again.
6)
Test the detector.
MAINTENANCE
-
BATTERY REPLACEMENT
When a low battery condition is indicated,
both batteries must be changed altogether.
During this procedure the linking switch must NOT
be touched at all !
1)
Detach the detector from its base.
2)
Extract the batteries cover.
3)
Extract the batteries.
4)
Insert the new batteries into their holders,
oriented as per polarity marks.
5)
Reinstall the batteries cover.
6)
Reinstall the detector onto its base.
7)
Test the detector.
Table 4
TECHNICAL SPECIFICATIONS **
Communication range with the
translator or expander
200 m
Open space
Operating frequency
868 MHz
Operating frequency channels
7
Radiated power
≤ 14
dBm (25 mW)
Batteries type*
Type CR123A (3 Vdc)
Primary battery lifespan
7.2 years life
Secondary battery lifespan
43 days life (after
primary battery low
fault)
Approved battery voltage range
2.85
-
3.2V
Parent expander
’
s check
-
up period
60 seconds (default setting)
Alarm threshold temperature.
Class A1R ROR
58 °C
Alarm threshold temperature.
Class B
-
high temperature
78 °C
Dimensions
110 mm x 65 mm
Weight
200 g
Base and batteries
included
IP rating
40
Max tolerated humidity
(no condensing)
95% RH
Operating temperature range
From –
10
°C to +55 °C
WARNINGS AND LIMITATIONS
Our devices use high quality electronic components and plastic materials that are highly resistant to
environmental deterioration. However, after 10 years of continuous operation, it is advisable to replace
the devices in order to minimize the risk of reduced performance caused by external factors. Ensure
that this device is only used with compatible control panels. Detection systems must be checked,
serviced and maintained on a regular basis to confirm correct operation. Smoke detectors may respond
differently to various kinds of smoke particles, thus application advice should be sought for special
risks. Detectors cannot respond correctly if barriers exist between them and the fire location and may
be affected by special environmental conditions. Refer to and follow national codes of practice and
other internationally recognized fire engineering standards. Appropriate risk assessment should be
carried out initially to determine correct design criteria and updated periodically.
WARRANTY
All devices are supplied with the benefit of a limited 5 years warranty relating to faulty materials or
manufacturing defects, effective from the production date indicated on each product. This warranty is
invalidated by mechanical or electrical damage caused in the field by incorrect handling or usage.
Product must be returned via your authorized supplier for repair or replacement together with full
information on any problem identified. Full details on our warranty and product
’
s returns policy can be
obtained upon request.
Hyfire Wireless Fire Solutions Limited
-
Unit
B12a, Holly Farm Business Park, Honiley,
Warwickshire, CV8 1NP
-
United Kingdom
EN 54
-
25:2008
EN 54
-
5:2000
Class A1R & BS
EN 54
-
7:2000+A1:2002+A2:2006
EN 54
-
31:2014+A1:2016
Programmable MT/NT category
HFW
-
TRI
-
05
For use in compatible fire detection and
alarm system
NOTE OF THE DOCUMENT:
Argus Security Srl hereby declares that this detector is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC. A copy of the original Declaration of Conformity
(Document: DoC LI01) is made available to the user on website: www.argussecurity.it
* When a low battery condition is indicated, both batteries must be changed for new cells.
Lifespan of batteries indicated is subject to standard environmental conditions default
monitor settings and excellent link quality.
** Check latest version of document TDS
-
LDMCO for further data, obtainable from your
supplier.
Hyfire Wireless Fire Solutions Limited
-
Unit B12a, Holly Farm Business Park, Honiley,
Warwickshire, CV8 1NP
-
United Kingdom
www.hyfirewireless.com
2831/0051/0681
0832
21
HF
-
20
-
043CPR
22
HF
-
20
-
043UK