manualshive.com logo in svg

Hydronix Hydro-Control VI, Installation Manual

Share
Download
Hydronix Hydro-Control VI Installation Manual Download Page 45

Chapter 4 

Commissioning 

 

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0 

45 

6.4 

The Sensor Configuration Screen – Page 4 

The Next button displays the fourth screen as shown in Figure 31. 

 

Figure 31: The sensor configuration screen - Page 4 

Temperature 

This section displays the current temperature readings. 

Temperature Extremes 

This section displays the maximum and minimum temperatures that the sensor has had whilst 

being powered up. 

Firmware 

This section displays the current firmware version number and checksum for diagnostics 

purposes. 

IO Status 

This section displays the current state of the digital inputs and outputs and other internal signals. 

Comms 

This section displays the total communication messages between the Hydro-Control and the 

sensor along with the error count. The error count can be used to identify communication 

issues. 

Analogue Output Test 

If the ‘Analogue Output Test’ button is pressed then this displays the window, shown in Figure 

32, which allows the two analogue outputs to be forced to known values.  This is useful for 

checking connections with external systems. 

 

Figure 32: The Analogue Output Test Controls 

Summary of Contents for Hydro-Control VI









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands