manualshive.com logo in svg

Hydronix Hydro-Control VI, Installation Manual

Share
Download
Hydronix Hydro-Control VI Installation Manual Download Page 44

Commissioning 

Chapter 4 

44 

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0 

6.3 

The Sensor Configuration Screen – Page 3 

The Next button displays the third screen as shown in Figure 30. 

 

Figure 30: The sensor configuration screen - Page 3 

Factory Settings 

This section allows the factory calibration of the sensor to be set.  This is necessary if the sensor 

is a Hydro-Probe Orbiter and the arm is changed or if the sensor is a Hydro-Mix and the ceramic 

faceplate is replaced. 

To set the factory calibration, make sure the sensor faceplate is in air and then press the ‘Read 

Air’ button.  After a short delay, the new air frequency and amplitude settings will be displayed 

in the entry boxes.  Next hold the sensor so that the faceplate is immersed in water as per the 

instructions in the sensor user guide and press the ‘Read Water’ button. 

An alternative method to the factory calibration is to use the Automatic Calibration function.  

This can be used to simplify the factory calibration process.  After the Automatic Calibration is 

performed, it may be necessary to recalibrate the recipes. 

To use the Automatic Calibration function, make sure that the sensor faceplate is in air and 

press the AutoCal button.  After a short delay the Hydro-Control will display an indication as to 

whether the AutoCal was successful or not. 

Orbiter Arms 

This section allows the Arm Type to be set. 

Temperature Compensation Coefficients 

This section allows the temperature compensation parameters to be changed.  It may be 

necessary to change these settings when using a Hydro-Probe Orbiter and changing the Orbiter 

Arm.  An Engineering Note is included with relevant Orbiter Arms which details the settings that 

must be entered.  With certain Hydro-Mix sensors these coefficients are set for each sensor in 

the factory and should not be changed. 

Measurement Mode 

This allows different measurement modes to be selected. 

If any settings are changed then they should be downloaded to the sensor using the ‘Write To 

Sensor’ button. 

Summary of Contents for Hydro-Control VI









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands