manualshive.com logo in svg

Hydronix Hydro-Control VI, Installation Manual

Share
Download
Hydronix Hydro-Control VI Installation Manual Download Page 18

Mechanical Installation 

Chapter 2 

18 

Hydro-Control VI Installation Guide HD0455 Rev 1.9.0 

HC06 v1

HC06 v2

 

Figure 5: View of the Hydro-Control VI showing the mounting brackets 

2  Mounting and installation 

The unit should be mounted in a control panel (maximum thickness 8mm) using a bracket on each 

side, two brackets on the top and two brackets on the bottom.  To fit the side brackets, locate the 

bracket in the slots on the side of the unit and slide it down until the top and bottom of the bracket 

are level with the case.  To fit the top and bottom brackets, insert the bracket into the slot and 

tighten the bolt. 

To install the Hydro-Control 

•

  Cut out an aperture in the panel of the correct size.  See Figure 6 for a template. 

•

  Remove the mounting brackets from the body of the unit by releasing the screws and then 

unhooking the brackets. 

•

  Insert the Hydro-Control through the prepared hole. 

•

  Re-fit the mounting brackets to the unit and tighten the screws evenly to pull the fascia 

towards the control panel. 

 
 

Panel or Enclosure

Cut-out for

Hydro-Control

232mm (9.14")

178mm (7.01")

 

Figure 6: The panel cut-out for the Hydro-Control VI 

Summary of Contents for Hydro-Control VI









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands