Hydro Doors Digidor III Manual Download Page 2

III

@

 Contents

III

@

10 CONTACT INFORMATION

2

19

1. Introduction

p3

2. Important Safety Instructions

p3

3. Battery Disposal

p3

4. Contents of the Box

p4

5. Features and Specifications

p5

6. General Issues

p6

Types of doors to be automated
Condition of doors
Manufacturer's Warranty

7. Assembly and Installation of the digidoor III ac/dc

p7

Power head and Strut assembly

Automation of sectional overhead doors

p7

Automation of tip-up (trackless one-piece) doors

p10

Automation of roll-up doors

p11

Electrical Connections and Set-up

p12

Visual and audible indications

p13

Wireless Wall Console

 

p13

Auto-close function

p13

Lock function

p14

Factory reset

p14

8. Using the digidoor III ac/dc on-board receiver

p14

Digi e key 

Recording a new transmitter via the wireless wall console
Erasing Transmitters

External connections

p15

9. Accessories

Battery backup

p16

Emergency key release

p17

Safety beams

p17

Important notes to installers and end users

p18

Service record

p18

HEAD OFFICE, JHB FACTORY & WAREHOUSE

Address: 

1334 Staal Road, Stormill Ext 2, Florida 1709 Roodepoort

Postal Address: 

PO Box 635 Florida 1710 South Africa

Telephone:  

+27 11 474 9060

Facsimile: 

+27 11 474 9067 / 8739

Website:

www.hydrodoors.co.za

Email: [email protected]

LAMBERT ANDERSON WOOD TRAINING ACADEMY (DIVISION OF HYDRO DOORS)

Telephone:  

+27 11 474 9060 

Facsimile: 

+27 11 474 9067 

Email: 

[email protected]

HYDRO BRANCHES:  

NATIONAL SALES NUMBER 0861 22 3444 (digi)

EAST RAND BRANCH - JOHANNESBURG

 

Address: 

Unit17, Lakeside Jet Park,
Corner of Kelly & Estee Ackerman Street,
Jet Park

Telephone:   +27 11 397 8448
Facsimile:

+27 11 397 8480         

Email:

[email protected]

PRETORIA BRANCH 

 

Address: 

Unit 6E & 6W, Coachmen's Park
26 Jakaranda Street, Hennopspark
Centurion, Pretoria 

Telephone:   +27 12 653 6399 
Facsimile: 

+27 12 653 6464

Email:

[email protected]

NELSPRUIT BRANCH

Address: 

Unit 10, Makspro Building
23 Waterfall Avenue
Riverside Industrial Park, Nelspruit   

Telephone:   +27 13 753 2176
Facsimile: 

+27 13 752 2636

Email:

[email protected]

DURBAN BRANCH

Address: 

8 Leeukop Road, Westmead, 
Pinetown, Durban

Telephone:   +27 31 700 2110
Facsimile: 

+27 31 700 2111

Email:

[email protected]

CAPE TOWN BRANCH    

Address: 

Unit 8  Brasant Park, 
Jan Smuts Road, Beaconvale, 
Parow, Cape Town

Telephone:   +27 21 933 5556
Facsimile: 

+27 21 933 5558

Email:

[email protected]

PORT ELIZABETH BRANCH    

Address: 

Unit 5 
Willow Road Business Park
33 Willow Road Fairview
Port Elizabeth

Telephone:   +27 41 367 2874
Facsimile: 

+27 41 367 3164

Email:

[email protected]

Summary of Contents for Digidor III











Reviews: