background image

15

01/03

P/N 211348D

Item Qty.

Part No.

Description

1

4

206677

J-Bolt, 1/2”-13 x 24”

2

8

202459

Nut, Hex 1/2”-13

3

1

920578

Mounting Plate

4

34*

203474

Washer, Flat 1/2” x 1” O.D.

5

1

980830

Pole

6

1

220590

Pole Cap, Square

7

11

206340

Nylon Insert Lock Nut, Hex 1/2”-13

8

8

220589

Cap, Arm Support Insert

9

2

906658

Support Arm, 42” Long, (Upper)

10

2

906678

Support Arm, 52” Long, (Lower)

11

2

220586

Logo Label, 15” x 1 3/4”

12

4

220588

Bolt, Hex Flange 1/2”-13 x 9”

13

1

908058

H-Frame

14

1

206685

Foam Roll

15

1

206681

Foam Pad, 4” x 28”

16

4

202856

Bolt, Hex Head,1/2”-13 x 4”

17

1

906277

Bracket, Jack Support (Left)

18

1

906276

Bracket, Jack Support (Right)

19

3

220048

Bolt, Hex Flange, 1/2”-13 x 6”

20

1

220064

Spacer, 5 x 1/2” O.D.

21

2

206311

Spacer, Black .53” x 1/2” 

22

4

203113

Bolt, Hex Flange 5/16”-18 x 2 1/2” 

Item Qty.

Part No.

Description

23

8

203100

Nut, Hex Flange 5/16”-18

24

8

203218

Washer, Flat 5/16” x 7/8” O.D.

25

1

920263

Rim, Orange

26

4

201611

Bolt, Hex Flange, 5/16”-18 x 3”

27

5*

203232

Washer, 3/4 O.D.

28

1

200484

Spring

29

1

200323

Washer, Flat, 1.5"

30

1

201124

Nut, Hex Locking, 5/16-18

31

1

960043

Cover Plate, Orange

32

2

220140

Screw, Self Tapping, 1/4 - 20 x 1/2

33

1

220569

Label Logo Circle

34

1

204282

Net

35

1

220565

Label, Height Indicator

36

1

206555

Pole Pad (May Not Be Included)

37

1

201262

Label, Height Adjustment

38

4

200517

Bolt Covers

39

1

920262

Bracket, Orange

40

1

920038

Inner Bracket, Black

41

1

220065

Bolt, Carriage 3/8 x 5 1/2

42

2

203063

Nut, Hex Nylon Locking 3/8

43

1

203017

Nut, Hex 3/8

44

1

203439

Bolt, Hex 3/8 x 6 

* You May Have Extra Parts With This Model.

PARTS LIST 

Item #16 (4)

Item #22 (4)

Item #2 (8)

HARDWARE IDENTIFIER

Item #4 (34)*

Item #19 (3)

Item #7 (11)

Item #20 (1)

Summary of Contents for 211348D

















Reviews: