background image

 

Always handle PCBs by their sides and avoid touching any components.  

 

PCBs should also be stored in a clean dry place, which is free from  

 

vibration, dust and excessive heat and is protected from mechanical  

 damage. 

 WARNING: Do not attempt to install this equipment until you have fully  
 

read and understood this manual.   

 

Failure to do so may result in damage to the equipment and could  

 

invalidate the warranty.  

 
 

For technical support please contact Hydor. Do not call the Hydor  

 

support department unless your distributor has first given their advice and  

 

attempted to rectify the issue. 

 
 

Technical support will 

not

 

be available if the instruction manual has  

 

not been read and understood. Please have this instruction manual  

 

available whenever you call for technical support. 

3. 

Control Panel

3.1  It is important these Installation and Maintenances are fully adhered to.
3.2  Full details of the control panel supplied are showed on the product  
 

nameplate and the circuit diagrams forwarded with the panel. If in doubt  

 

about any detail contact Hydor or its agents for clarification.

3.3  All electrical installations must be carried out by qualified and competent  
 

personnel in accordance with all current statutory requirements.

3.4  These instructions cover only the Hydor product and do not include the  
 

supply or installation of any safety equipment that may be required, e.g.  

 

proper electrical isolation.

3.5  All declarations made by Hydor about the product installation and safety,  
 

are dependent on the control panel being used within installations which 

  

themselves meet the requirements of the relevant Standards and  

 

Directives of the region.

3.6  The control panel is designed for use in an ambient temperature of up to  
 

50°C and 95% relative humidity. The control panel is NOT suitable for  

 

corrosive or explosive atmospheres unless stated.

3.7  It is the Installer’s responsibility to provide easy access to the control 
 

panel to facilitate future maintenance.

3.8  This product is not intended for the use of young children or infirm  
 

persons unless they have been adequately supervised by a responsible  

 

person to ensure they can use the product safely. Young children should  

 

be supervised to ensure they do not play with the appliance.

Summary of Contents for Bespoke









Reviews: