HYDAC FILTER SYSTEMS FCU1315 Operating And Maintenance Instructions Manual Download Page 23

Page: 23 / 185

4 |

HYDAC FILTER SYSTEMS

18 /

BeWa FCU1315 4168086b

Counting contaminant particles optically (light

blockade procedure)

The measuring principle of the light blockade procedure is

shown in simplified form in the following sketch.

The light source transmits monochromatic light through the

flow of oil to a photo detector, which produces a particular

electrical signal. If a particle gets between the light source and

the photo detector, then a shadow will be cast on the photo de-

tector.

This shadow causes a change in the electrical signal gener-

ated by the photo detector. This change makes it possible to

determine the size of the shadow cast by the particle and thus

to gauge the size of the particle itself.

This procedure makes it possible to determine the cleanliness

class according to ISO 4406, NAS 1638 and SAE AS 4059.

The disruption factors of this measurement principle are, for

example, foreign fluids and small gas bubbles that lead to re-

fractions, thus causing them to be counted as particles as well.

Fig. 4: Light blockade procedure

1 Light source

2 Contaminant particle

3 Photo detector

Summary of Contents for FCU1315


























































































































































































Search results

Summary of Contents for FCU1315

Reviews:

Related manuals for FCU1315

Brands by name

Popular brands

HYDAC FILTER SYSTEMS FCU1315, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for FCU1315

Reviews:

Related manuals for FCU1315

Brands by name

Popular brands