HYDAC FILTER SYSTEMS CTM-EF 3 3 Series Operating And Maintenance Instructions Manual Download Page 20

Page: 20 / 64

3 | Overview

HYDAC FILTER SYSTEMS GMBH

20 / 64

BeWa CTM-EF3x3x 4436386 en-us lq

3.4 Technical Data

Depending on the size and version, the

CTM-EF

has varying technical data.

CTM-EF 343x

CTM-EF 363x

Test liquid volume

40 liters

60 liters

Empty weight

≈ 110 kg

Dimensions

600 x 600 x 1550 mm

Rated voltage

85 … 265 V AC, 50 / 60 Hz

Nominal power

100 W

Tab. 5: Technical data - CTM-EF3x3x

Protection class according to

EN 60529/DIN 40050

IP 44

Permissible environmental conditions

Air and temperature similar to labora-

tory conditions, the room is adequately

ventilated

Permissible ambient temperature

range

15 … 28°C

Permissible relative air humidity

≤ 80% (non condensing)

Permissible storage temperature range 0 … 50°C

Required compressed air supply

5 … 6 bar

Required cleanliness of compressed

air

ISO8573-1 [7:4:4]

Permissible air conditions during stor-

age

Dust-free, salt-free air, not near oxidiz-

ing substances (rust film)

Permitted relative air humidity

≤ 80% (non condensing)

Design life expectancy of the device

The design life expectancy of the de-

vice is not limited if the service and

maintenance intervals are complied

with.

Life expectancy of the components of

the device with safety functions.

Semtron load disconnector/emergency

stop switch 3LD2122-0TK13: Maxi-

mum switching cycles, 50 per hour

Summary of Contents for CTM-EF 3 3 Series

































































Search results

Summary of Contents for CTM-EF 3 3 Series

Reviews:

Related manuals for CTM-EF 3 3 Series

Brands by name

Popular brands

HYDAC FILTER SYSTEMS CTM-EF 3 3 Series, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for CTM-EF 3 3 Series

Reviews:

Related manuals for CTM-EF 3 3 Series

Brands by name

Popular brands