Hyd-Mech H18A-120 Manual Download Page 51

Page: 51 / 80

3.6

CAM FOLLOWER ADJUSTMENT

There are two cam followers mounted on the head frame. The set of cam followers are shown below. One of them is fixed

and the other is adjustable. The cam followers are factory set and usually do not require adjustment. In a properly

adjusted system of cam followers only one side should be in contact with the guide. The gap between the other and the

guide bar should be 0.003” – 0.005”. If it exceeds 0.005” you should contact your dealer to arrange for adjustment.

LUBRICATION

The design of the machine was intended to minimize maintenance, although periodically certain moving parts need

lubrication. We recommend that this periodic lubrication be done once a month using any general purpose grease. In

addition to the grease points shown, vise jaw guides, in-feed rollers and bundling assemblies require greasing.

2 SHUTTLE

SHAFT BEARING HOUSINGS

4 GUIDE ARM GREASE

POINTS

IDLER WHEEL TENSIONER

(ONE AT BOTH ENDS)

CAM FOLLOWER GREASE

NIPPLES

2 SHUTTLE VISE GREASE NIPPLES

Summary of Contents for H18A-120

















































































Search results

Summary of Contents for H18A-120

Reviews:

Related manuals for H18A-120

Brands by name

Popular brands

Hyd-Mech H18A-120, Manual

Search results

Summary of Contents for H18A-120

Reviews:

Related manuals for H18A-120

Brands by name

Popular brands