background image

2

TABLE OF CONTENTS

1. Safety Instructions

..................................................................................................... 2

2. Technical Specifications

...........................................................................................3

3. How To Control The Unit

.......................................................................................4

4. How to use the remote controller................................................................................8
5

. Trouble shooting

........................................................................................................9

statement

The

product

has

well

capability

and

intact

packing

when

leave

factory. All of the user should comply with warning item and manual, any
misuse cause of the damages are not included in our guarantee, and
also can not be responsible for any malfunction & problem owing to
ignore the manual.

1. Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using

the unit.

Before operating, ensure that the voltage and frequency of power

supply match the power requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order

to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

Summary of Contents for HMH GOBO













Reviews: