Hy-Gain THUNDERBIRD TH6-DX Instruction Manual Download | Manualshive

Page: 11 / 22

background image

Page 13

2-12

LIGHTNING PROTECTION

For lightning protection you must ground your antenna supporting structure. A
proper ground consists of a 1/2"

x

8' ground rod driven into the ground as

close as possible to the base of your tower or mast. Connect the rod to the
tower or mast using a copper strap or 12 gauge copper or aluminum wire.

For total protection of your equipment it is highly recommended that you
obtain a Hy-Gain Model LA-1 lightning arrestor. The Model LA-1 is
available at your local Hy-Gain dealer.

THIS COMPLETES YOUR INSTALLATION OF THE TH6-DX. SIMPLY
ATTACH YOUR FEEDLINE TO THE RF CHOKE AND HAPPY DX'ING.

«
...
9
10
11
12
13
...
»

Summary of Contents for THUNDERBIRD TH6-DX























Reviews:

No comments

Related manuals for THUNDERBIRD TH6-DX

Brand: M2 Antenna Systems Pages: 3

Brand: Opticum Red Pages: 4

Brand: Mohu Pages: 9

StreetPilot 7200

Brand: Garmin Pages: 76

Brand: 2J Antennas Pages: 3

Brand: ZinWave Pages: 31

Brand: Steren Pages: 21

Brand: M-Life Pages: 16

Brand: TCi Pages: 2

Brand: A.H. Systems Pages: 14

Brand: REP Pages: 4

airGrid M5 AGM5-HP-1724

Brand: Ubiquiti Pages: 20

Brand: Taoglas Pages: 2

Brand: CUSHCRAFT Pages: 8

Brand: 3Z TELECOM Pages: 2

Brand: YDI Pages: 28

Brand: Maco Antennas Pages: 6

Twin Flat 00044303

Brand: Hama Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands