HWH 725 SERIES Service Manual Download Page 12

Page: 12 / 50

MI91.327E

01NOV11

If there is no ground on pin D8 of the harness connector,

the problem is the #9000 wire, the wire

SEE: MP84.3130

connection to the 32 pin connector, the connection of the #9000 wire to the park brake switch out put
or something is wrong with the park brake switch.

If there is a ground on pin D8 of the harness connector, make sure the #9000 wire is properly

inserted into the connector. Give the wire a light pull. If the wire is loose in the connector, the pin may
not have good contact with the module pin. Check for any corrosion problems. If the wire and pin are
properly inserted into the 32 pin connector and the pin or socket are not corroded, use a voltmeter to
check voltage between the white and red wire in the 5 pin MTA connector on the back of the touch
panel. If there is less than 10.5 volts at the touch panel, voltage to the I/O module should be

Ground for the I/O module (and touch panel) is a 14 gauge wire coming out of the top of the I/O module,
not the brass ground stud on the module. If voltage to the module is low, check all ground connections
and the voltage source. If voltage to the module is good but there is low voltage coming from the
module to the touch panel, make sure all connections for the red 6800 wire on pin B1 and white 6230
wire on pin B3 are good. If all wires and connections are good, replace the I/O module.
at the touch panel is good, replace the I/O module. SEE: MP84.3170 and MP84.3334

2. With the park brake released, the "NOT IN PARK/BRAKE" light does not come on when a
DOWN arrow is pushed. Push any UP arrow. If the "NOT IN PARK/BRAKE" light is not coming

on, the pump should run.

IF THE PUMP RUNS with the park brake released, either the #9000 park brake wire has a ground

on it or the I/O module is bad.

Unplug the 32 pin connector at the I/O module. The black #9000 park brake wire is on pin D8. Make
sure the park brake is released. Use a test light connected to a +12 source such as the battery supply
side of the master relay to check pin D8 for a ground. SEE: MP84.3170 and MP84.3130

If there is a ground on pin D8, the #9000 park brake wire is shorted to ground,

improperly connected or there is a problem with the park brake switch.

there is a problem with the I/O module and it should be replaced.

If there is no ground on pin D8 of the harness connector,

checked. Ign./Acc. voltage to the I/O module is on pin D1 in the 32 pin connector at the I/O module.

If voltage

connected to a +12 source such as the battery supply side of the master relay to check pin D8 for a

32 pin connector at the I/O module. The black #9000 park brake wire is on pin D8. Use a test light

There should be a ground on the park brake wire (9000) with the park brake set. Unplug the

1. With the park brake set, the "NOT IN PARK/BRAKE" light comes on while pushing a DOWN

and push any DOWN arrow on the touch panel. The "NOT IN PARK/BRAKE" light should come on.

The "NOT IN PARK/BRAKE" light should not come on. Release the park brake

A. With the ignition in the ON or ACC. position and the park brake set, push any DOWN arrow

THE VEHICLE CAN ROLL FORWARD OR BACKWARD CAUSING INJURY OR DEATH.

CHOCK THE VEHICLE WHEELS BEFORE RELEASING THE PARK BRAKE.

It is also important that the park brake circuit is functioning properly and that the system

The system will not function if the park brake is not set.

SEE: MP84.3170

Reset the park brake.

on the touch panel.

arrow.

ground.

WARNING:

cannot function with the park brake released.

PART 5. PARK BRAKE CHECK.

MANUAL OPERATION

725 TROUBLE SHOOTING STEPS

NOTE: Contact the vehicle manufacturer for information concerning the park brake switch
or the connection of the HWH 9000 wire to the park brake switch.

MP84.3170

3 2

PUMP RELAY

MASTER RELAY

LINK LIGHT

DUMP

TRAVEL

MP84.3170

MASTER RELAY

A
B
C
D

3 2

PUMP RELAY

LINK LIGHT

TRAVEL

DUMP

MP84.3334

PIN 4

LINK LIGHT

PIN 1

MP84.3170

MASTER RELAY

7 6

C
D

LINK LIGHT

PUMP RELAY

TRAVEL

DUMP

WARNING

DIAGRAM - SENSING UNIT

SWITCH

SEE ELECTRICAL CONNECTION DIAGRAM
LEVELING SYSTEM HYDRAULIC MANIFOLD

SEE ELECTRICAL CONNECTION

RESISTOR

PRESSURE SWITCH

MULTIPLEXED INPUT/OUTPUT MODULE

SEE ELECTRICAL CONNECTION DIAGRAM

TOUCH PANEL - JACK WARNING LIGHTS AND PRESSURE SWITCHES

PARK BRAKE - MASTER WARNING LIGHT AND BUZZER

725 SERIES SINGLE STEP LEVELING SYSTEM

ELECTRICAL CONNECTION DIAGRAM

DO NOT CUT

TERMINATING

9001 - TO

DIODE

PARK BRAKE
LIGHT

PRESSURE SWITCH

NOTE: DIODE ARRANGEMENT MAY NOT BE

4000

4200

6235

PRESENT ON ALL INSTALLATIONS

6120 - TO +12V ACC.

WARNING
SWITCH

15 AMP

FUSE

WARNING

BUZZER

6111

12V IGNITION

CONNECT TO

SWITCH

9000

1000

DIODE

6111

SWITCH

PARK BRAKE

7699

WARNING

MASTER

LIGHT

7699

1200

FUSE
5AMP

SWITCH

PRESSURE

6235

TOUCH PANEL

UNDERSTAND OPERATOR’S MANUAL BEFORE USING. BLOCK FRAME AND TIRES

SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.

HWH COMPUTERIZED LEVELING

MANUAL

DO NOT CUT

LEVEL

AUTO

AUTO
STORE

EXTEND

EXCESS
SLOPE

PARK/

NOT IN

RETRACT

TRAVEL
MODE

WARNING!

CANCEL

BRAKE

RESISTOR

TERMINATING

EXTEND

RETRACT

6235

3000

3200

MP84.3130

08JUN11

SWITCH

WARNING

8101

8100

6235

PUMP AND MASTER RELAYS

2200

PRESSURE

SWITCH

2000

MP84.3130

ELECTRICAL CONNECTION DIAGRAM

725 SERIES SINGLE STEP LEVELING SYSTEM

PARK BRAKE - MASTER WARNING LIGHT AND BUZZER

TOUCH PANEL - JACK WARNING LIGHTS AND PRESSURE SWITCHES

SEE ELECTRICAL CONNECTION DIAGRAM

MULTIPLEXED INPUT/OUTPUT MODULE

PRESSURE SWITCH

RESISTOR

SEE ELECTRICAL CONNECTION

LEVELING SYSTEM HYDRAULIC MANIFOLD

SEE ELECTRICAL CONNECTION DIAGRAM

SWITCH

DIAGRAM - SENSING UNIT

WARNING

DIODE

9001 - TO

TERMINATING

DO NOT CUT

NOTE: DIODE ARRANGEMENT MAY NOT BE

PRESSURE SWITCH

LIGHT

PARK BRAKE

4000

4200

6235

6120 - TO +12V ACC.

PRESENT ON ALL INSTALLATIONS

SWITCH

WARNING

FUSE

15 AMP

9000

SWITCH

CONNECT TO
12V IGNITION

6111

BUZZER

WARNING

1000

7699

PARK BRAKE
SWITCH

6111

DIODE

WARNING

LIGHT

MASTER

7699

5AMP

FUSE

1200

PRESSURE
SWITCH

6235

MANUAL

HWH COMPUTERIZED LEVELING

SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.

UNDERSTAND OPERATOR’S MANUAL BEFORE USING. BLOCK FRAME AND TIRES

TOUCH PANEL

DO NOT CUT

STORE

AUTO

AUTO
LEVEL

BRAKE

CANCEL

WARNING!

MODE

TRAVEL

RETRACT

NOT IN
PARK/

SLOPE

EXCESS

EXTEND

TERMINATING

RESISTOR

RETRACT

EXTEND

6235

3000

3200

08JUN11

MP84.3130

WARNING

SWITCH

8101

8100

6235

PUMP AND MASTER RELAYS

2200

SWITCH

PRESSURE

2000

Summary of Contents for 725 SERIES



















































Search results

Summary of Contents for 725 SERIES

Reviews:

Related manuals for 725 SERIES

Brands by name

Popular brands

HWH 725 SERIES, Service Manual

Search results

Summary of Contents for 725 SERIES

Reviews:

Related manuals for 725 SERIES

Brands by name

Popular brands