height adjusting stop in the 3" hole, and turning the height stop so
that the flat side is against the stop handle. Fig. 5-13
5.
Clamp the height adjusting stop against the stop handle (5-13). This
will assure that the height will not move during the setting process.
Otherwise, spring pressure from the deck lift springs will tend to pull
the stop away from the handle.
6.
Loosen all nuts on the deck lift threaded rods, and the hardware on
the adjuster (on the right front), until
all
the deck lift chains are
loose,
and
the deck is sitting tightly on all four blocks. Fig. 5-14, 5-
15, 5-16
7.
Loosen the two nuts on the front of height indicator so that the foot
pedal is free. Fig. 5-17
8.
Start the leveling process on the
left front
of the tractor.
9.
Set the amount of threads protruding on the deck lift rod from the lift
block at approximately 1". Fig. 5-18
10.
Jam both nuts against the block.
11.
Push or pull on the deck lift foot pedal until the
chain on the left
front
just becomes tight, making sure that the deck stays tight
against the 3" block.
12.
While keeping the chain tight, tighten the nuts against the deck lift
block on the height indicator rod. Fig. 5-17
13.
Go to the
right front
of the tractor.
14.
Loosen the 5/16" jam nut on the adjuster lift chain (5-16), and back
the adjuster bolt out to allow the adjuster to move up and down
freely.
15.
Be sure that adjuster is free to move up and down.
16.
Tighten the adjuster bolt until the chain just becomes tight, making
sure that the deck stays tight against the 3" block.
17.
Tighten the adjuster bolt jam nut to prevent the adjuster bolt from
moving. Fig. 5-16
18.
Tighten the hardware holding the chain and adjuster onto the deck
lift arm.
19.
Go to the
right rear
of the tractor.
20.
Make sure that there is still slack in the chain. If not, loosen the two
nuts on the block holding the threaded rod until there is slack in the
deck lift chain. Fig. 5-15
21.
Tighten the appropriate nut until the chain just becomes tight,
making sure that the deck stays tight against the 3" block.
22.
Tighten the other nut on the opposite side of the block, and jam them
tightly together against the block.
23.
Go to the
left rear
of the tractor.
24.
Make sure that there is still slack in the chain. If not, loosen the two
nuts on the block holding the threaded rod until there is slack in the
deck lift chain. Fig. 5-14
25.
Tighten the appropriate nut until the chain just becomes tight.
26.
Tighten the other nut on the opposite side of the block, and jam them
tightly together against the block.
Figure 5-16
5/16” bolt
Adjuster
Hardware
Jam nut
Figure 5-15
Deck lift
threaded
rod
Nut
N
Nu
utt
Chains
Figure 5-14
Deck lift threaded rod
N
Nu
utt
Nut
Chains
Figure 5-12
Blocks
Figure 5-13
Height
adjusting
stop
Stop
handle
5-4
365270 Rev. 9/03
365270 Rev. 9/03
Summary of Contents for FasTrak 926501
