Hussmann TY3ECRC Installation & Operation Manual Download Page 20

20

• USE WATER AND A MILD DETERGENT FOR THE  

EXTERIOR ONLY

• Wipe interior with damp non-abrasive cloth. Soap and  

hot water are not enough to kill bacteria; a sanitizing  
solution must be included with each cleaning process to  
eliminate bacteria.

• Clean any visible debris surrounding or on top of the  

drain location. The drain is located under the deck pans.

• DO NOT USE A CHLORINATED CLEANER ON ANY  

SURFACE.

• DO NOT USE ABRASIVES OR STEEL WOOL SCOUR-

ING PADS (these will mar the finish)

• DO NOT Use a cleaning or sanitizing solution that

has:

• OIL BASE (these will dissolve the  butyl

sealants)

• AMMONIA BASE (these will corrode the

copper components of the case)

• ACID Base (these will pit and damaged 

metal finishes

• DO Not Use chlorinated sanitizing solutions

General Maintenance

Inspect and clean condenser coil monthly. Clean
using a vacuum cleaner with a wand attachment 
and a soft (non-metallic) brush to remove dirt and 
debris. DO NOT bend fins. Always wear gloves and 
protective eyewear when cleaning near sharp coil 
fins and dust particles. When properly  cleaned, you 
should be able to see through the  condenser coil

Inspect drain screens for debris. Remove if present. 
DO NOT put debris down the drain

Inspect honeycomb for dust buildup. Remove and 
clean with water and mild soap

Ensure no price tags, placards, debris, or 
merchandising garnish is sitting in the return air

Ensure shelves are not stocked outside of their limits 
(See Load limit representation on page 22)

Case Cleaning

To ensure long life, proper sanitation and minimum 
maintenance costs, the refrigerator should be thoroughly 
cleaned frequently. SHUT OFF FAN BEFORE 
CLEANING: It can be unplugged within the case, or shut 
off entire case at the source. The interior bottom may be 
wiped with any domestic soap or detergent based 
cleaners.

WARNING! DO NOT USE WATER HOSES!

A self

contained case empties into an evaporator pan that WILL 
OVERFLOW IF TOO MUCH WATER IS INTRODUCED
during cleaning

Plexiglass and Acrylic Care

Improper cleaning not only accelerates the cleaning cycle
but also degrades the quality of this surface. Normal daily
buffing motions can generated static cling attracting dust to
the surface. Incorrect cleaning agents or cleaning cloths can
cause micro scratching of the surface, causing the plastic to
haze over time.

Hussmann recommends using a clean damp chamois, or a
paper towel marked as “dust and abrasive free” with 210

®

Plastic

Cleaner and Polish available by calling Sumner Labs at 1-800-
542-8656. Hard, rough cloths or paper towels will scratch the
acrylic and should not be used.

Sanitizing

It is essential to establish a regular cleaning procedure.
This will minimize bacteria causing discoloration which leads
to degraded product appearance and significantly shortening
product shelf life.
Soap and hot water are not enough: A sanitizing solution
must be included with each cleaning process to eliminate
this bacteria. Sanitizing solutions will not harm the interior
bottom, however, these solutions should always be within
the following guidelines:

1. Scrub thoroughly, cleaning all surfaces, with soap  

and hot water.

2. Rinse with hot water, but do not flood.
3. Apply the sanitizing solutions that meet the 

guidelines above.

4. Rinse thoroughly.
5. Dry completely before resuming operation.

Summary of Contents for TY3ECRC



























Reviews: