background image

EXTERIOR LOADING

Do NOT walk on top of merchandisers

 or  

damage to the merchandisers and serious  
personal injury could occur. 

merchandisers

 

are

 

not

 

structurally

 

designed

 

to

 

support

 

external

 

loading

 

such as the weight of a person. Do not place 
heavy objects on the merchandiser.

SHIPPING SKID

Each merchandiser is shipped on a skid to  
protect the merchandiser’s base, and to make  
positioning the case easier.

Do not remove the shipping skid until the  
merchandiser is near its final location.

 

The 

skid provides protection for both the merchan-
diser and the floor.

Remove the skid by raising one end of the  
merchandiser approximately 6 inches. Block the 
merchandiser securely, and remove the two skid 
bolts from the raised end. Replace the bolts 
with (provided) leg levelers. Repeat this proce-
dure at opposing end. Once the leg levelers are 
secured in place, the merchandiser may be slid 
off the skid and placed in its final location.

DO NOT TILT MERCHANDISER ON ITS 
SIDE OR END WHEN REMOVING SKID.

Once the skid is removed, the merchandiser 
must be lifted —NOT PUSHED— to reposition. 

Check floor where merchandisers are to be set 
to see if it is a level area. Determine the highest 
part of the floor.

MERCHANDISER LEVELING

B

e

 

sure

 

to

 

position

 

merchandisers

 

proper

-

ly

Level the merchandiser by all four corners. 

Merchandiser(s) must be installed level to 
ensure proper operation of the refrigeration 
system, and to ensure proper drainage of 
defrost water. 

OPTIONAL LEGS

NSF

® 

approved legs replace the leg levelers if 

required by local health codes. The legs raise 
the case 6 inches for cleaning purposes. An 
optional skirt kit can be provided to snap on 
the legs. 

P/N 0545719_B

 

1-3

HUSSMANN CORPORATION • BRIDGETON, MO  63044-2483  U.S.A.

GSVM Open Vertical Merchandisers

This product may contain chemicals known 

to the State of California to cause cancer, 

birth defects, or other reproductive harm.

This warning is the result of the California State 
law known as the California Safe Drinking Water 
and Toxic Enforcement Act of 1986, which is 
commonly referred to as “Proposition 65.”

This warning does not mean that Hussmann 
products will cause cancer or reproductive 
harm, or is in violation of any product-safety 
standards or requirements. As clarified by the 
California State government, Proposition 65 
can be considered more of a ‘right to know’ law 
than a pure product safety law. When used as 
designed, Hussmann believes that our products 
are not harmful. We provide the Proposition 65 
warning to stay in compliance with California 
State law. It is your responsibility to provide 
accurate Proposition 65 warning labels to your 
customers when necessary. For more information 
on Proposition 65, please visit the California 
State government website.

For California Businesses:

Summary of Contents for GSVM 4060D











































Reviews: