7
ASSEMBLY
FIG. 3
02466
02464
SEAT PAN
SHOULDER
BOLT
ADJUSTMENT
KNOB
FLAT WASHER
SEAT
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment knob.
• Remove adjustment knob and fl at washer securing
seat to cardboard packing and set aside for assembly
of seat to tractor.
• Pivot seat upward and remove from the cardboard pack-
ing. Remove the cardboard packing and discard.
• Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan.
• Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor.
• Pivot seat and pan forward and assemble adjustment
knob and fl at washer loosely. Do not tighten.
• Lower seat into operating position and sit on seat.
• Slide seat until a comfortable position is reached
which allows you to press clutch/brake pedal all the
way down.
• Get off seat without moving its ad just ed position.
• Raise seat and tighten adjustment knob securely.
ASSEMBLE GAUGE WHEELS TO MOWER
DECK (See Fig. 4)
The gauge wheels are designed to keep the mower deck in
proper position when operating mower. Be sure they are prop er ly
adjusted to ensure optimum mower per for mance.
• Slide gauge wheel bar down into bracket channel, Be sure
that gauge wheel bar aligning holes are on top. As sem ble
gauge wheels as shown using shoulder bolts, 3/8 washers
and 3/8-16 center locknuts and tighten securely.
• For ease of mower to tractor assembly, raise gauge
wheels to highest position and retain with clevis pins
and spring retainers.
• Adjust gauge wheels before operating mower. See “TO
ADJUST GAUGE WHEELS” in the Operation sec tion
of this manual.
SHOULDER
BOLT
AD JUST ING
BAR
PIN
RETAINER SPRING
FIG. 4
GAUGE
WHEEL
3/8-16 CENTER
LOCKNUT
3/8 WASH ER
NOTE:
You may now roll or drive your tractor off the skid.
Follow the ap pro pri ate instruction below to remove the
tractor from the skid
.
TO ROLL TRACTOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
• Press lift lever plunger and raise attachment lift lever
to its highest po si tion.
• Release parking brake by de press ing brake ped al.
• Place freewheel control in "trans mis sion dis en gaged
position" (See “TO TRANS
PORT” in the Op
er a tion
section of this manual).
• Roll tractor forward off skid.
TO DRIVE TRAC
TOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
WARNING:
Before start ing, read, un der stand and fol low
all in struc tions in the Op er a tion section of this man u al. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
• Be sure all the above assembly steps have been com-
pleted.
• Check engine oil level and fi ll fuel tank with gasoline.
• Place freewheel control in "trans
mis sion en
gaged"
po si tion (see "TO TRANSPORT" in Op er a tion section
of this manual).
• Sit on seat in operating position, depress brake pedal
and set the parking brake.
• Place motion control lever in neutral (N) position.
• Press lift lever plunger and raise attachment lift lever
to its highest position.
• Start the engine. After engine has started, move throttle
control to idle position.
• Release parking brake.
• Slowly move the mo tion control lever for ward and slowly
drive tractor off skid.
• Apply brake to stop trac tor, set park ing brake and place
motion con trol lever in neutral po si tion.
• Turn ignition key to "STOP" position.
Continue with the in struc tions that follow.
02180
TERMINAL
ACCESS
DOOR
HEX
BOLT
POSITIVE
(RED)CABLE
NEGATIVE
(BLACK)CABLE
KEPS NUT
DISCARD
TERMINAL
PROTECTIVE
CAPS
FIG. 2