manualshive.com logo in svg

Husqvarna WH3616, Operator'S Manual

Share
Download
Husqvarna WH3616 Operator'S Manual Download Page 42

teCHnICal Data

42

WH3616

WH4818

Engine

manufacturer

Kawasaki 

1, 2)

Kawasaki 

1, 2)

Type

FS

FS

Power

16 hp* / 12 kW

18 hp* / 13 kW

Fuel

min 87 octane unleaded (max 

ethanol 10%, max mTbe 15%)

min 87 octane unleaded (max 

ethanol 10%, max mTbe 15%)

Fuel tank capacity

6 gallons / 22.7 liters

6 gallons / 22.7 liters

Cooling

Air cooled

Air cooled

Air filter

Dual element

Dual element

Alternator

12V

12V

Starter

Recoil

Recoil

Transmission

Transmission

Hydraulic Pump

Hydraulic Pump

Speed and direction controls

Speed forward

0-7.0 mph / 0-11.3 km/h

0-7.0 mph / 0-11.3 km/h

Speed reverse

0-2.5 mph / 0-4.0 km/h

0-2.5 mph / 0-4.0 km/h

brakes

mechanical parking brake

mechanical parking brake

Front caster tires, smooth tread

9 x 3.50-4, 4 ply

9 x 3.50-4, 4 ply

Rear tires, turf pneumatic

16 x 7.5-8

16 x 7.5-8

Tire pressure

15 PSI / 103 kPa / 1 bar

15 PSI / 103 kPa / 1 bar

Equipment

Cutting Width

36" / 91 cm

48" / 122 cm

Cutting Height

1.5 - 5" / 3.8 - 12.7 cm

1.5 - 5" / 3.8 - 12.7 cm

Productivity

1.8 acres /h 7290 m

2

/h

2.4 acres /h 9720 m

2

/h

Overall Dimensions

Weight

535 lbs / 243 kg

550 lbs / 249 kg

Overall machine length

73" / 185 cm

71" / 180 cm

base machine Height

38-45" / 96.5-114 cm

38-45" / 96.5-114 cm

base machine Width

35" / 89 cm

40" / 102 cm

Overall Width, Chute Up

36¼" / 92 cm

48¾" / 124 cm

Overall Width, Chute Down

48¼" / 122.5 cm

60¾" / 154 cm

1)

 

See the engine manufacturer's manual for engine 

specifications.

2)

 

The power rating of the engines indicated is the average 

net power output (at specified rpm) of a typical production 
engine for the engine model measured to SAe standard 
J1349/ISO1585. mass production engines may differ from 
this value. Actual power output for the engine installed 
in the final machine will depend on the operating speed, 
environmental conditions and other variables.

Summary of Contents for WH3616





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands