manualshive.com logo in svg

Husqvarna TS 250 XS, Operator'S Manual, Page: 5 / 20

Share
Download
Husqvarna TS 250 XS Operator'S Manual Download Page 5

5

•  Motor Off

•  Parar El Motor

•  Use In Well Ventilated Area

•  Usar En Una Área Bien Ventilada

•  Do Not Use In Flammable Areas

•  No Usar In Áreas Inflamables

•  Machinery Hazard, Keep Hands And Feet Clear.

•  Máquina Peligrosa - Mantenga Manos Y Pies Alejados De La Máquina

•  No Non-working Personnel In Area

•  Prohibido Para Personas Ajenas A La Obra

•  No Smoking

•  No Fumar

•  Do Not Operate Without All Guards In Place

•  No Operar Sin Todas Las Protecciones In Su Sitio

•  Always Keep the Blade Guards In Place

•  Mantenga Siempre Las Protecciones De La Hoja En Su Sitio

•  Keep Work Area Clean/Well Lit, Remove All Safety Hazards

•  Mantenga Limpio El Sitio De Trabajo/Bien Iluminado, Elimine Todos Los Riesgos De Seguridad

•  Dangerously High Noise Level

•  Nivel De Ruido Elevadamente Peligroso

•  Pay Extreme Attention To The Care And Protection Of The Machine Before Starting Up

•  Ponga Extrema Atención Al Cuidado Y Preparación De La Máquina Antes De Ponerla En Marcha

•  Remove Tools From Area and Machine

•  Elimine Las Herramientas Del Área Y De La Máquina

•  Electrical Switch - OFF

•  Conmutador De Apagado Eléctrico

 

•  Electrical Switch - ON

•  Conmutador De Encendido Eléctrico

•  Electrical Switch - Start

•  Conmutador De Arranque Eléctrico

Summary of Contents for TS 250 XS





















Reviews:

No comments