Husqvarna TE 250 Owner'S Manual Download

Page: 151 / 169

TECHNICAL DATA 23

149

Nut, inner clutch hub

M18x1.5

100 Nm (73.8 lbf ft)

Loctite

243™

Nut, primary gear wheel

M18LHx1.5

150 Nm (110.6 lbf ft)

Loctite

243™

23.3

Capacities

23.3.1

Gear oil

Gear oil

0.80 l (0.85 qt.)

Engine oil (15W/50) (

p. 155)

23.3.2

Coolant

Coolant

1.2 l (1.3 qt.)

Coolant (

p. 155)

23.3.3

Fuel

Total fuel tank capacity, approx.

8.5 l (2.25 US gal)

Super unleaded (ROZ 95)

(

p. 156)

Fuel reserve, approx.

1.5 l (1.6 qt.)

2-stroke oil tank content approx.

0.6 l (0.6 qt.)

Engine oil, 2-stroke (

p. 155)

23.4

Chassis

Frame

Central tube frame made of chrome molybdenum

steel tubing

Fork

WPXPLOR 5548

Shock absorber

WPXACT 5750

Suspension travel

front

300 mm (11.81 in)

rear

300 mm (11.81 in)

Fork offset

22 mm (0.87 in)

Brake system

Disc brakes, floating brake calipers

Brake discs - diameter

front

260 mm (10.24 in)

rear

220 mm (8.66 in)

Brake discs - wear limit

front

2.5 mm (0.098 in)

rear

3.5 mm (0.138 in)

Street tire pressure (All EU/AR standard models)

front

2.0 bar (29 psi)

rear

2.0 bar (29 psi)

Offroad tire pressure

front

1.0 bar (15 psi)

rear

0.8 bar (12 psi)

Secondary ratio (TE 250 EU)

14:52 (13:52)

Secondary ratio (TE 300 EU, TE 300 AR)

14:50 (13:50)

Secondary ratio (TE 250 US, TE 250 CN)

13:52

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands