Husqvarna TC 50 2023 Owner'S Manual Download

Page: 83 / 196

BRAKE SYSTEM 12

V02100-10

Main work

–

Move the brake fluid reservoir mounted on the handlebar into

a horizontal position.

–

Remove screws

–

Take off cover

with membrane

–

Correct the brake fluid level.
Guideline

Brake fluid level under top

level of container

5 mm (0.2 in)

Brake fluid DOT 4 / DOT 5.1 (

p. 137)

–

Position the cover with the membrane. Mount and tighten the

screws.

Info

Clean up the overflowed or spilled brake fluid immedi-

ately with water.

12.7

Checking the front brake linings

Warning

Danger of accidents

Worn-out brake linings reduce the braking effect.

–

Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy-

cles workshop will be glad to help.)

A00088-10

–

Check the brake linings for minimum thickness

Minimum thickness

≥

1 mm (

≥

0.04 in)

» If the minimum thickness is less than specified:

–

Change the brake linings of the front brake.

(

p. 81)

–

Check the brake linings for damage and cracking.
» If damage or wear is encountered:

–

Change the brake linings of the front brake.

(

p. 81)

12.8

Changing the brake linings of the front brake

Warning

Danger of accidents

Incorrect servicing will cause the brake system to fail.

–

Ensure that service work and repairs are performed professionally. (Your authorized Husqvarna

Motorcycles workshop will be glad to help.)

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands