Husqvarna TC 50 2023 Owner'S Manual Download

Page: 29 / 196

RIDING INSTRUCTIONS 8

400214-10

–

Fill the fuel tank with fuel up to level

Guideline

Level

35 mm (1.38 in)

Fuel tank capacity,

approx. (TC 50 MINI)

2.3 l (2.4 qt.)

Super unleaded

(ROZ 95)

(

p. 138)

Fuel tank capacity,

approx. (TC 50)

2.3 l (2.4 qt.)

Super unleaded

(95 octane) mixed

with 2-stroke

engine oil (1:60)

(

p. 138)

–

Close the fuel tank filler cap. (

p. 16)

8.9

Filling up with oil (TC 50 MINI)

Warning

Engine damage

The engine will not be lubricated unless there is 2-stroke oil in the oil tank.

–

For a full fuel tank, fill the oil tank at least up to the

MIN

mark.

–

Switch off the engine.

–

Open the oil tank cap. (

p. 16)

A00094-11

–

Fill the oil tank at least up to the

MIN

mark

Guideline

MIN

mark

Sufficient for a single tank

filling

Oil tank contents ca.

0.2 l (0.2 qt.)

Engine oil, 2-stroke

(

p. 137)

–

Close the oil tank cap. (

p. 17)

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands