Husqvarna TC 50 2023 Owner'S Manual Download

Page: 18 / 196

6 CONTROLS

Warning

Danger of poisoning

Fuel is harmful to health.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

Rinse the affected area immediately with plenty of water in the event of contact with the skin.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing if fuel spills on them.

–

Keep fuels correctly in a suitable canister, and out of the reach of children.

Note

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

F02222-10

–

Turn fuel tank filler cap

counterclockwise and lift it off.

6.5

Closing the fuel tank filler cap

F02222-11

–

Mount the fuel tank filler cap and turn it clockwise until the

fuel tank is tightly closed.

Info

Route fuel tank breather hose

without kinks.

6.6

Opening oil tank cap (TC 50 MINI)

A00092-10

–

Turn the oil tank cap

counterclockwise and pull it up.

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands