Husqvarna TC 50 2023 Owner'S Manual Download

Page: 135 / 196

TECHNICAL DATA 21

133

Steering head angle (TC 50)

66°

Steering head angle (TC 50 MINI)

67.4°

Wheelbase (TC 50)

1,032 ± 10 mm (40.63 ± 0.39 in)

Wheelbase (TC 50 MINI)

914 ± 10 mm (35.98 ± 0.39 in)

Seat height unloaded (TC 50)

665 mm (26.18 in)

Seat height unloaded (TC 50 MINI)

558 mm (21.97 in)

Ground clearance unloaded (TC 50)

252 mm (9.92 in)

Ground clearance unloaded (TC 50 MINI)

184 mm (7.24 in)

Weight without fuel approx. (TC 50)

41.5 kg (91.5 lb.)

Weight without fuel approx. (TC 50 MINI)

40 kg (88 lb.)

Maximum rider weight

45 kg (99 lb.)

21.6

Tires

Validity

Front tire

Rear tire

(TC 50)

60/100 - 12 36J TT

MAXXIS MAXXCROSS MX

‑

2.75 - 10 38J TT

MAXXIS MAXXCROSS MX

‑

(TC 50 MINI)

60/100 - 10 33J TT

MAXXIS MAXXCROSS MX

‑

2.75 - 10 38J TT

MAXXIS MAXXCROSS MX

‑

The tires specified represent one of the possible series production tires. For alternative manufacturers, if any,

contact an authorized dealer or qualified tire dealership. If local road approval regulations apply, these and

the respective technical specifications must be observed. Additional information is available in the Service

section under:
www.husqvarna

‑

motorcycles.com

21.7

Fork

21.7.1

TC 50

Fork article number

07.18.6U.02

Fork

WP XACT 5235

Rebound damping

Comfort

15 clicks

Standard

12 clicks

Sport

10 clicks

Air pressure

2 bar (29 psi)

Fork length

685 mm (26.97 in)

Spring length with preload spacer(s)

337.5 mm (13.287 in)

Oil capacity external mechanism

left

25 ± 5 ml (0.85 ± 0.17 fl. oz.)

Fork oil (SAE 4) (48601166S1)

(

p. 137)

Oil capacity, right cartridge

225 ml (7.61 fl. oz.)

Fork oil (SAE 4) (48601166S1)

(

p. 137)

Grease capacity, left cartridge

6 g (0.21 oz)

Special grease (00062010053)

(

p. 140)

21.7.2

TC 50 MINI

Fork article number

07.18.1U.01

Fork

WP XACT 5035

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands