Husqvarna TC 50 2023 Owner'S Manual Download

Page: 115 / 196

SERVICE WORK ON THE ENGINE 16

113

M01537-10

–

Remove screws

–

Take off the oil pump.

–

Pull off oil line

from the carburetor.

V00276-10

–

Turn oil pump gear wheel

counterclockwise until oil flows

out of oil line

without bubbles.

M01537-10

–

Connect oil line

–

Position the oil pump.

–

Mount and tighten screws

Guideline

Screw, oil pump

6 Nm (4.4 lbf ft)

16.3

Checking the gear oil level

Condition

The engine is cold.

Preparatory work

–

Stand the motorcycle upright on a horizontal surface.

K01172-11

Main work
(TC 50 MINI)

–

Remove screw

–

Check the gear oil level.

A small quantity of gear oil must run out of the drilled

hole.

» If no gear oil runs out:

–

Add the gear oil.

(

p. 115)

–

Mount and tighten screw

Guideline

Screw, gear oil

level monitoring

6 Nm (4.4 lbf ft)

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands