manualshive.com logo in svg

Husqvarna HUV 4214 2009, Maintenance And Service Manual

Share
Download
Husqvarna HUV 4214 2009 Maintenance And Service Manual Download Page 57

ACCELERATOR AND BRAKE PEDAL GROUP

Brake Pedal Installation

5

4.

Remove bow-tie locking pins and washers securing each end of brake pedal pivot rod to bracket

(Figure 5-21,

Page 5-9)

.

5.

Slide pedal to one side and remove from vehicle.

1192

Figure 5-21

Remove Brake Pedal Bow-Tie Locking Pins

BRAKE PEDAL INSTALLATION

1.

Maneuver brake pedal into position in bracket and secure with washers and bow-tie locking pins.

2.

Secure pedal to master cylinder push rod with clevis pin and rue pin.

3.

Install under-pedal closeout panel with new rivets.

4.

Connect battery and spark plug wire(s).

See Connecting the Battery – Gasoline Vehicles on page 1-4.

BRAKE PEDAL ADJUSTMENT

1.

Loosen the master cylinder rod and clevis jam nut.

2.

Rotate the master cylinder rod to extend or retract the clevis and brake pedal to the desired position.

3.

Tighten the jam nut to 168 in-lb (19 N·m).

4.

Perform all brake system inspections to ensure that the hydraulic brake system and the park brake system are
adjusted and operating correctly before the vehicle is returned to service.

See Brake System Inspection,

Section 6, Page 6-4.

2009-2010 HUV 4214, HUV 4414, and HUV 4414X Maintenance and Service Manual

Page 5-9

Summary of Contents for HUV 4214 2009




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands