Husqvarna FE 450 Owner'S Manual Download Page 121

Page: 121 / 128

25 STANDARDS

119

JASO T903 MA

Different technical development directions required a new specification for 4-stroke motorcycles

–

the JASO T903 MA Standard.

Earlier, engine oils from the automobile industry were used for 4-stroke motorcycles because there was no separate motorcycle

specification. Whereas long service intervals are demanded for automobile engines, high performance at high engine speeds are

in the foreground for motorcycle engines. In most motorcycles, the gearbox and the clutch are lubricated with the same oil as the

engine. The JASO MA Standard meets these special requirements.

SAE

The SAE viscosity classes were defined by the Society of Automotive Engineers and are used for classifying oils according to their

viscosity. The viscosity describes only one property of oil and says nothing about quality.

Summary of Contents for FE 450

































































































































Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands

Husqvarna FE 450, Owner'S Manual

Search results

Summary of Contents for FE 450

Reviews:

Related manuals for FE 450

Brands by name

Popular brands