Husqvarna F2303V4 Owner'S Manual Download Page 134

Page: 134 / 168

18 SERVICE WORK ON THE ENGINE

132

Info

Drain the engine oil with the engine at operating temperature.

Preparatory work

–

Remove the engine guard. (

p. 89)

–

Park the motorcycle on a level surface.

F00441-10

Main work

–

Position an appropriate container under the engine.

–

Remove oil drain plug

with the magnet and seal ring.

F00442-10

–

Remove screw plug

with the short oil screen and the O-

rings.

Info

Do not remove screw

F00443-10

–

Remove screw plug

with long oil screen

and the O-

rings.

–

Allow the engine oil to drain completely.

–

Thoroughly clean the parts and the sealing surfaces.

F00442-11

–

Mount and tighten screw plug

with the short oil screen

and the O-rings.
Guideline

Screw plug, oil
screen

M20x1.5

15 Nm (11.1 lbf ft)

Summary of Contents for F2303V4









































































































































































Search results

Summary of Contents for F2303V4

Reviews:

Related manuals for F2303V4

Brands by name

Popular brands

Husqvarna F2303V4, Owner'S Manual

Search results

Summary of Contents for F2303V4

Reviews:

Related manuals for F2303V4

Brands by name

Popular brands