Husqvarna F2303U7 Owner'S Manual Download | Manualshive

Page: 90 / 171

background image

13 BRAKE SYSTEM

88

13.3

Checking the front brake fluid level

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the specified marking or the specified value, the brake system is
leaking or the brake linings are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized
Husqvarna Motorcycles workshop will be glad to help.)

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service
schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

H03717-10

–

Move the brake fluid reservoir mounted on the handlebar to a
horizontal position.

–

Check the brake fluid level in level viewer

1

.

» When the brake fluid level has dropped to lower edge

A

of the level viewer:

–

Add front brake fluid.

13.4

Adding front brake fluid

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the specified marking or the specified value, the brake system is
leaking or the brake linings are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized
Husqvarna Motorcycles workshop will be glad to help.)

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact
with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service
schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

«
...
88
89
90
91
92
...
»

Summary of Contents for F2303U7












































































































































































Reviews:

No comments

Related manuals for F2303U7

Brand: DAELIM Pages: 20

Brand: Ohlins Pages: 8

Brand: Cobra Pages: 38

Brand: R&G Pages: 6

Brand: hepco & becker Pages: 5

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 7

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 3

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 2

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 3

Brand: RIEJU Pages: 280

Brand: RIEJU Pages: 152

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands