Husqvarna F2275U4 Page 85 Owner'S Manual Download

Page: 85 / 162

SERVICE WORK ON THE CHASSIS 12

12.38

Checking the frame

F00255-01

–

Check the frame for cracks and deformation.
» If the frame exhibits cracks or deformation due to a

mechanical impact:

–

Change the frame.

Info

Always replace a frame that has been
damaged due to a mechanical impact. Repair
of the frame is not authorized by Husqvarna
Motorcycles.

12.39

Checking the link fork

401520-01

–

Check the link fork for damage, cracking, and deformation.
» If the link fork exhibits damage, cracking, or deformation:

–

Change the link fork.

Info

Always replace a damaged link fork. Repair of
the link fork is not authorized by Husqvarna
Motorcycles.

12.40

Checking throttle cable routing

Preparatory work

–

Remove the air filter box cover. (

p. 68)

–

Remove the seat. (

p. 66)

–

Remove the right side cover. (

p. 70)

–

Remove the fuel tank.

(

p. 75)

Summary of Contents for F2275U4



































































































































































Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands

Husqvarna F2275U4, Owner'S Manual

Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands