manualshive.com logo in svg

Husqvarna 968999252, Operator'S Manual

Share
Download
Husqvarna 968999252 Operator'S Manual Download Page 3

3

Table of Contents

SAFETY .................................................................................................................... 4
EQUIPMENT SETUP AND ADJUSTMENTS ............................................................. 5
CUTTING HEIGHT ..................................................................................................... 5
MOWER DECK LEVELING ...................................................................................... 5
MOTION CONTROL ADJUSTMENT .......................................................................... 6
BELT ADJUSTMENTS .............................................................................................. 6
INTERLOCK SAFETY SYSTEM ............................................................................... 6
NEUTRAL LOCK ADJUSTMENT .............................................................................. 7
GROUND SPEED NEUTRAL ADJUSTMENT ........................................................... 7
GROUND SPEED LEVER FRICTION ....................................................................... 7
OPERATING INSTRUCTIONS ................................................................................... 8
MAINTENANCE INSTRUCTIONS ............................................................................. 9
MAINTENANCE CHART .......................................................................................... 12
TROUBLE SHOOTING ............................................................................................. 13

©2004 Husqvarna. All right reserved.

Beatrice, NE. Printed in U.S.A.

Summary of Contents for 968999252















Reviews:

No comments

Brands by name

Popular brands

Load more brands