background image

ENGLISH - 9

Drawing out the string

During cutting, the nylon string wears naturally 
causing an increase in the speed of the engine 
and a reduced cutting capacity. When this 
happens, to bring out more string bump the head 
against the ground: release the throttle trigger to 
reduce the engine speed to less than 8000 rpm. 
Tap gently on the ground with the button (

A

) as 

shown in the figure and the string will come out 
automatically. Accelerate again. If the string 
does not come out make sure there is still some 
left and try again.

Thinning grass with the grass cutter blade

 

The grass is cut with swinging motions from side 
to side, maintaining the blade parallel to the 
ground. During the right to left swing the grass is 
cut, while the backswing must be made without 
using the blade.

I2.

 KICKBACK can occur when cutting is done 

with the risk sector of the blade; we recommend 
cutting with the rest of the blade. Take care that 
the cup supporting the blade just grazes the 
ground. This will prevent the blade from touching 
the ground.

Use of sawtooth blade

 

 

 

The sawtooth blade serves to cut bushes and 
small trees, with maximum diameter of seven 
centimeters. Rest the left side of the special 
shield on the trunk while cutting to limit the risk of 
losing control of the machine.

This section contains information useful for 
maintaining the characteristics of eco-
compatibility included in the origin design of the 
machine, and as regards proper use and 
disposal of oil and fuel.

Design

In the design stage, care was taken to develop 
an engine with reduced consumption and low 
emissions of noise and pollutant exhaust fumes.

Use of machine

The operations of filling the tank with the fuel 
mixture should be carried out in such a way as to 

avoid spilling fuel and contaminating the soil and 
environment.

Periods of prolonged disuse

Always empty the fuel tank with the same 
precautions used in filling it.

Disposal

Do not dispose inappropriately of the machine 
when it is no longer usable. Deliver it to an 
authorized organization for proper disposal in 
compliance with the regulations in force.

The engine continues to have problems: contact your authorized supplier

 

2 16

Do not attempt to cut trees with a larger 
than recommended diameter, to prevent 
the risk of kickback or damage to the 
blade.

2

5 11 16

L. Environmental information

M. Troubleshooting table

The engine does 
not start

The engine 
stutters or loses 
power

The machine 
starts but does 
not cut properly

Make sure the STOP switch is on “I”.

Make sure that the fuel tank is at least 25% 
full.

Make sure the air filter is clean.

Remove the sparkplug, dry and clean it, 
then return it to its place. If necessary, 
replace it.

Change the fuel filter. Contact your 
supplier.

Follow the correct procedure for assembly 
of the cutting accessories.

Make sure the metal accessories are sharp, 
and contact your supplier if necessary.

Summary of Contents for 953900767














Reviews: