Husqvarna 8527SBE Owner'S Manual Download Page 27 | Manualshive

Page: 27 / 32

background image

27

KEY PART
NO. NO.

DESCRIPTION

   1   532 14 63-15   Screw, Hex Head 5/16-18 x 3/4
   2   873 80 05-00   Nut, Lock 5/16-18
   3   532 15 54-15   Washer, Flat
   4   817 49 05-08   Screw, Hex Head 5/16-18 x 1/2
   5   532 18 00-17   Bearing, Flange
   6   532 18 01-34   Shaft, Auxiliary
   7   532 17 92-70   Spacer, Plate
   8   532 19 29-07   Plate, Auxiliary
   9   532 18 00-82   Gear, Intermediate (12/58)

10 532 18 00-65 Gear, Pinion

11 532 18 77-14 Rod, Clutch

12   532 18 00-66   Shaft, Long, Hex
13   532 17 88-07   Pin, Pivot
14   532 18 40-80   Lever, Shifter / Wheel
15   532 17 53-44   Trunnion Bearing Assembly
16   532 18 78-57   Bracket, Pivot, Shift
17   532 17 98-31   Ring, Rubber Wheel
18   532 19 95-09   Plate, Rubber Wheel
19   873 93 05-00   Nut, Lock 5/16-18
20   532 17 86-13   Hub, Rubber Wheel
21   874 76 05-14   Screw, Hex Head 5/16-18 x 7/8
22   532 08 51-79   Retainer, Hairpin
23   532 18 01-35   Spring, Bias
24   532 18 00-81   Gear, Axle (58 Teeth)
25   532 17 86-95   Pin, Pivot Lever
26   532 19 77-63   Plate Assembly, Drive
27   532 17 93-52   Shaft, Axle
28   532 19 77-64   Shaft, Short Hex
29   532 18 40-77   Lever, Shifter Plate
30   532 18 40-76   Bracket, Shifter Support
31   872 27 05-05   Bolt, Carriage 5/16-18 x 5/8
32   532 18 92-82   Key, Square
33   532 18 89-09   Bearing, Flange
34   532 18 40-75   Plate, Drive Mounting
35   532 18 25-04   Spacer, Bearing
36   532 19 10-80   Pulley, Traction Drive
37   532 15 53-77   Nut, Lock 5/16-18
38   819 11 15-07 Washer, Flat
39   810 04 05-00   Washer, Lock 5/16
40   874 95 05-12   Screw, Hex Head 5/16-18 x 3/4
41   812 00 00-12   Ring, Retaining
42   811 05 05-00 Washer, Lock, External Tooth 5/16
43   532 17 90-95   Spring, Return
44   532 18 42-06   Pin, Roll

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO.

8527SBE

(96193000300), PRODUCT NO. 961 93 00-03

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your lawn mower and void your warranty.

«
...
25
26
27
28
29
...
»

Summary of Contents for 8527SBE

































Reviews:

No comments

Related manuals for 8527SBE

Brand: Remington Pages: 32

Brand: Gardol Pages: 188

Brand: Douglas Dynamics Pages: 4

Brand: York Pages: 20

Brand: Feider Machines Pages: 27

Brand: HIKOKI Pages: 48

Brand: Jonsered Pages: 272

Brand: YARDMAX Pages: 32

Brand: Cub Cadet Pages: 52

Brand: White Outdoor Pages: 22

Brand: Cub Cadet Pages: 32

Brand: Kongskilde Pages: 60

Brand: Troy-Bilt Pages: 28

Brand: Troy-Bilt Pages: 29

Groundsmaster 7200 Series

Brand: Toro Pages: 72

Brand: Shark Pages: 14

Brand: Shark Pages: 16

Brand: Sweepster Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands