Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 126

Page: 126 / 216

14 WHEELS, TIRES

124

S01057-10

Warning

Danger of accidents

Damaged brake discs reduce the braking effect.

–

Always lay the wheel down in such a way that the brake disc is not dam-

aged.

–

Holding the front wheel, withdraw the wheel spindle. Take the front wheel out of the

fork.

Info

Do not pull the hand brake lever when the front wheel is removed.

H00934-10

–

Remove spacers



14.2

Installing the front wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands