Husqvarna 701 Enduro 2017 Owner'S Manual Download Page 117

Page: 117 / 216

13 BRAKE SYSTEM

115

S01052-10

–

Loosen fittings



on foot brake cylinder



–

To adjust the basic position of the foot brake lever to individual requirements, loosen

nut



and turn screw



accordingly.

Info

The range of adjustment is limited. The screw must be screwed into the

footrest bracket by at least four turns.

–

Position foot brake cylinder



so that the foot brake lever has the necessary free

travel.

–

Tighten fitting



Guideline

Screw connection, foot brake cylinder

10 Nm (7.4 lbf ft)

–

Check the free travel of the foot brake lever. (

p. 113)

–

Tighten nut



13.10

Checking the rear brake fluid level

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the

MIN

marking, the brake system is leaking or the brake linings are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized Husqvarna Motorcycles

workshop will be glad to help.)

Summary of Contents for 701 Enduro 2017

























































































































































































































Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands

Husqvarna 701 Enduro 2017, Owner'S Manual

Search results

Summary of Contents for 701 Enduro 2017

Reviews:

Related manuals for 701 Enduro 2017

Brands by name

Popular brands