Husqvarna 335LS Operator'S Manual Download Page 6

 

GENERAL SAFETY PRECA

 

UTIONS

 

6

 

 – 

 

English

 

Impor

 

tant

Personal protective equipment

 

HELMET

 

A protectiv

 

e helmet where there is a risk of falling objects

HEARING PROTECTION

Wear hearing protection that provides adequate noise 
reduction.

EYE PROTECTION

Always wear approved eye protection. If you use a visor then 
you must also wear approved protective goggles. Approved 
protective goggles must comply with standard ANSI Z87.1 in 
the USA or EN 166 in EU countries.

GLOVES

Gloves should be worn when necessary, e.g., when fitting 
cutting attachments.

IMPORTANT!

The machine is only designed for trimming grass.

The only accessories you can operate with this engine unit 
are the cutting attachments we recommend in the chapter 
on Technical data.

Never use the machine if you are tired, if you have drunk 
alcohol, or if you are taking medication that could affect 
your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions 
under the heading Personal protective equipment.

Never use a machine that has been modified in any way 
from its original specification.

Never use a machine that is faulty. Carry out the checks, 
maintenance and service instructions described in this 
manual. Some maintenance and service measures must 
be carried out by trained and qualified specialists. See 
instructions under the heading Maintenance.

All covers, guards and handles must be fitted before 
starting. Ensure that the spark plug cap and ignition lead 
are undamaged to avoid the risk of electric shock.

The machine operator must ensure that no people or 
animals come closer than 15 metres while working. When 
several operators are working in the same area the safety 
distance should be at least twice the tree height and no 
less than 15 metres.

!

 

W

 

ARNING! The ignition system of this 

machine produces an electromagnetic field 
during operation. This field may under 
some circumstances interfere with 
pacemakers. To reduce the risk of serious 
or fatal injury, we recommend persons with 
pacemakers to consult their physician and 
the pacemaker manufacturer before 
operating this machine.

!

 

W

 

ARNING! Running an engine in a confined 

or badly ventilated area can result in death 
due to asphyxiation or carbon monoxide 
poisoning.

!

 

W

 

ARNING! Never allow children to use or 

be in the vicinity of the machine. As the 
machine is equipped with a spring-loaded 
stop switch and can be started by low 
speed and force on the starter handle, even 
small children under some circumstances 
can produce the force necessary to start 
the machine. This can mean a risk of 
serious personal injury. Therefore remove 
the spark plug cap when the machine is not 
under close supervision.

 

IMPOR

 

TANT!

A clearing saw, brushcutter or trimmer can be dangerous if 
used incorrectly or carelessly, and can cause serious or 
fatal injury to the operator or others. It is extremely 
important that you read and understand the contents of this 
operator’s manual.

You must use approved personal protective equipment 
whenever you use the machine. Personal protective 
equipment cannot eliminate the risk of injury but it will 
reduce the degree of injury if an accident does happen. 
Ask your dealer for help in choosing the right equipment.

!

 

W

 

ARNING! Listen out for warning signals 

or shouts when you are wearing hearing 
protection. Always remove your hearing 
protection as soon as the engine stops.

Summary of Contents for 335LS





































Reviews: