background image

 

GENERAL SAFETY PRECA

 

UTIONS

 

6

 

 – 

 

English

 

Impor

 

tant

Personal protective equipment

 

HEARING PR

 

OTECTION

Wear hearing protection that provides adequate noise 
reduction.

EYE PROTECTION

Always wear approved eye protection. If you use a visor 
then you must also wear approved protective goggles. 
Approved protective goggles must comply with standard 
ANSI Z87.1 in the USA or EN 166 in EU countries.

GLOVES

Gloves should be worn when necessary, e.g., when fitting 
cutting attachments.

BOOTS

Wear sturdy, non-slip boots or shoes.

IMPORTANT!

The machine is only designed for cutting branches and 
twigs.

Never use a machine that has been modified in any way 
from its original specification.

Never use the machine if you are tired, if you have drunk 
alcohol, or if you are taking medication that could affect 
your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions 
under the heading ”Personal protective equipment”.

Never use the machine in extreme weather conditions 
such as severe cold, very hot and/or humid climates.

Never use a machine that is faulty. Carry out the checks, 
maintenance and service instructions described in this 
manual. Some maintenance and service measures 
must be carried out by trained and qualified specialists. 
See instructions under the heading Maintenance.

All covers and guards must be fitted before starting. 
Ensure that the spark plug cap and ignition lead are 
undamaged to avoid the risk of electric shock.

!

 

W

 

ARNING! This machine produces an 

electromagnetic field during operation. 
This field may under some 
circumstances interfere with active or 
passive medical implants. To reduce the 
risk of serious or fatal injury, we 
recommend persons with medical 
implants to consult their physician and 
the medical implant manufacturer before 
operating this machine.

!

 

W

 

ARNING! Running an engine in a 

confined or badly ventilated area can 
result in death due to asphyxiation or 
carbon monoxide poisoning.

!

 

W

 

ARNING! Never allow children to use or 

be in the vicinity of the machine. As the 
machine is equipped with a spring-
loaded stop switch and can be started by 
low speed and force on the starter 
handle, even small children under some 
circumstances can produce the force 
necessary to start the machine. This can 
mean a risk of serious personal injury. 
Therefore remove the spark plug cap 
when the machine is not under close 
supervision.

!

 

W

 

ARNING! Faulty blades can increase 

the risk of accidents.

 

IMPOR

 

TANT!

Incorrect or careless use of a hedge trimmer can turn it 
into a dangerous tool that can cause serious or even 
fatal injury. It is extremely important that you read and 
understand the contents of this operator’s manual.

You must use approved personal protective equipment 
whenever you use the machine. Personal protective 
equipment cannot eliminate the risk of injury but it will 
reduce the degree of injury if an accident does happen. 
Ask your dealer for help in choosing the right equipment.

!

 

W

 

ARNING! Listen out for warning signals 

or shouts when you are wearing hearing 
protection. Always remove your hearing 
protection as soon as the engine stops.

Summary of Contents for 323HD60





























Reviews: