Husqvarna 1100 CD Service Manual Download | Manualshive

Page: 35 / 61

background image

104 72 30-26 Husqvarna service manual 35

18 IV The lengthwise movement of the feed dog

Requirements

The feed dog must not strike against the
stitch plate when the machine is set at
maximum stitch length and speed.

Adjustment

Set the machine at stitch length 0 mm
and the feed dog at its highest position.
Loosen the screw (A) and shift the feed
dog until it comes in the middle of the
stitch plate.
Tighten the screw.
Check according to requirements.

NOTE!

Check that the stitch setting fork (B) is parallel with
the connecting rod (C) after tightening.

19 The bobbin-winding device

Limiting when bobbin-winding

Requirements

When bobbin-winding the machine shall stop when the
bobbin is full with thread up to approx. 1 mm from the
edge of the bobbin.

Adjustment

Loosen the locking ring (A) by means of a tool.
Thereafter turn the scanner (B) until you switch off
when there is an adequate amount of
thread on the bobbin (see illustration).
After the adjustment the scanner is secured from
being turned by means of the locking ring.

SEWKNITWORLD

«
...
33
34
35
36
37
...
»

Summary of Contents for 1100 CD






























































Reviews:

No comments

Related manuals for 1100 CD

Brand: Meec tools Pages: 132

Brand: EINHELL Pages: 104

Brand: EINHELL Pages: 128

Brand: EINHELL Pages: 132

Brand: EINHELL Pages: 144

Brand: Zenoah Pages: 18

Brand: Zenoah Pages: 72

Brand: McCulloch Pages: 344

Brand: Tanaka Pages: 64

Brand: Makita Pages: 21

Brand: Surtek Pages: 20

Brand: Craftsman Pages: 23

Brand: Craftsman Pages: 24

Brand: Craftsman Pages: 22

Brand: Craftsman Pages: 19

Brand: Craftsman Pages: 32

Brand: Craftsman Pages: 18

Brand: Craftsman Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands