SPECIFICATIONS
• This appliance is intended strictly for domestic indoor use.
• The refrigerating circuit is leak-proof.
REVERSING THE DOOR HINGE
The door can be opened from left to right and vice versa. Should you wish to
change the opening direction, please follow these instructions.
Note:
all parts removed should be kept safely. You will require these for the
reinstallation of the door.
• Remove the two screws (1) that hold the upper hinge (5)(right side)
to the frame.
• Lift the door off and place on a padded surface to prevent scratching.
• Remove the blanking plug (8) from the hole in the upper left corner
of the door and transfer it to the uncovered hole on the upper right
corner. Press firmly to secure it.
• Remove the two screws (6) that hold the lower hinge (2)
• Remove the adjustable front left foot (4) and transfer it to the other
side.
• Remove the bolt pin(7) from the lower hinge (2) and reverse the
direction of the lower hinge. Secure the lower hinge (2) to the left
side of the lower frame with the two screws (6) Re-insert the bolt
pin (7). Set the door into position, making sure it is seated
comfortably onto the lower hinge (2).
• Holding the door closed, secure the upper hinge (5) into the top
frame with the two screws (1). Check the door is level and tighten
the screws firmly.
H U S k Y R E F R I G E R A T O R
5
HOW TO MINIMISE THE ENERGY CONSUMPTION OF YOUR
HUSKY REFRIGERATOR
• Energy consumption will be lower if the unit stands in a well
ventilated space and in particular if vent at the back of the unit is
clear of obstruction.
• Do not place the appliance in direct sunlight or near a heat source
such as ovens, radiators, heaters, etc as this will increase energy
consumption.
• keep the door closed as much as possible.
• Setting the thermostat cooler (towards 5 on the dial) means higher
energy consumption, so set only as cold as you require.
• Do not overfill the cabinet - overfilling means that the cool air cannot
circulate freely inside the cabinet which may slow the process of
cooling and make the cabinet less efficient.
• Defrost the appliance if frost can be seen building up inside - frost
will increase energy consumption and make the cooling process
slower.
• Turn the appliance off completely if it is not required for a period of
days or longer to avoid wasting energy (see also section ‘When not
in use’).
BASIC OPERATION
Your Husky Refrigerator must stand on an even surface.
If the appliance is to be placed on carpet, support it with a wooden board
underneath. Be aware that placing the appliance on carpet may mean that
heat from the compressor may cause the carpet to fade.
Thermostat settings
The settings 1 (MIN) – 5 (MAX) regulate the interior
temperature.
Setting 1 (or MIN) = lowest setting (warmest
internal temperature)
Setting 5 (or MAX) = highest setting (coldest
internal temperature)
To operate
1. Clean the inner compartment.
2. Plug in your Husky Refrigerator.
3. To turn the unit off, disconnect the plug from the mains supply.
NOTE:
If the unit is unplugged or power lost, you must wait 3 to 5 minutes
before restarting. If you attempt to restart the unit before this delay, the
unit will not start.
WARNING
If the thermostat is set to too cold a setting, beverages may become frozen.
In extreme circumstances, glass bottles may even break. Always exercise
caution when setting the temperature.
• Do not place heavy items (more than 20kg/44lbs) on top of the
refrigerator.
• Do not place any items on top of the refrigerator which may fall off
when the door is opened.
• After the appliance has been unplugged, leave for three minutes
before plugging it in again.
4
H U S k Y R E F R I G E R A T O R
Fig 1
Position of components
prior to reversal of the door hinge.
Fig 2
Position of components
after reversal of the door hinge.
HU Generic Solid Door manual 0616.indd 9-10
15/06/2016 15:56
