Huskee MC43ETSC Operator'S Manual Download

Page: 19 / 36

OPERATOR INSTRUCTIONS ANd PARTS

MC43ETSC & MC43TSC Cultivator

Page 1

GetEarthquake.com

800-45-6007

TROUBlEShOOTINg

PROBlEm

POSSIBlE CAUSE

REmEdY/ACTION

Engine will not start

1. Power switch off

1. Flip switch to ON position

2. Spark plug wire disconnected

2. Connect spark plug wire to spark plug

3. Out of fuel

3. Refuel

4. Spark plug wet, faulty or improperly
gapped

4. Clean, replace or gap spark plug

5. Throttle control not held open

5. Hold throttle control open when pulling recoil
handle

6. Fuel line hose not positioned in bot-
tom of gas tank

6. Push fuel line down into fuel in gas tank

Engine runs rough, floods during
operation

1. Dirty air filter

1. Clean or replace air filter

2. Choke partially engaged

2. Turn off choke

3. Carburetor out of adjustment

3. Call factory

Engine is hard to start

1. Stale fuel

1. Drain old fuel and replace with fresh.
Use gas stabilizer at end of season

2. Spark plug wire loose

2. Make sure spark wire is securely attached to
spark plug

3. Dirty carburetor

3. Clean carburetor, use gas stabilizer, new gas can

4. Throttle control not held open

4. Prime unit 3 more times, then hold throttle open
when pulling recoil handle

Engine misses or lacks power

1. Clogged gas tank

1. Remove and clean gas tank

2. Clogged air filter

2. Clean or replace air filter

3. Carburetor out of adjustment or bad

3. Call factory

4. Spark plug wet, faulty or improperly
gapped

4. Clean, replace or gap spark plug

Engine runs, then quits

1. Gas cap not venting

1. Clean or replace gas cap, check vent

2. Plugged fuel filter

2. Clean or replace fuel filter

3. Carburetor out of adjustment or bad

3. Call factory

Engine revs too high

1. Carburetor out of adjustment

1. Call factory

Tines turn at idle

1. Idle speed too high

1. Adjust idle speed lower

2. Broken clutch spring

2. Replace spring

mOdEl mC4ETSC ONlY

Charger won’t charge

1. Battery worn out

1. Replace with new batttery

2. Connectors not plugged in

2. Open battery box and connect battery connectors

Key won’t start machine

2. Battery not charged

1. Charge battery

Contact service provider at 800-345-6007 if above remedies fail.

Summary of Contents for MC43ETSC




































Search results

Summary of Contents for MC43ETSC

Reviews:

Related manuals for MC43ETSC

Brands by name

Popular brands

Huskee MC43ETSC, Operator'S Manual

Search results

Summary of Contents for MC43ETSC

Reviews:

Related manuals for MC43ETSC

Brands by name

Popular brands