HunterDouglas Vertiglide Applause Honeycomb Installation And Care Instructions Download Page 20 | Manualshive

Page: 20 / 52

background image

20

Space Evenly

Space Evenly

8"

8"

Installation Brackets

INSIDE MOUNT — BRACKET INSTALLATION

Mount The Brackets

Bracket Spacing

Measure and mark where to attach the installation brackets. Place installation

brackets 8" in from the ends of the shade.
Space additional brackets evenly between the two end brackets.

■

■

Attach Bracket Shim

Attach the shim to the top of the

mounting bracket. It snaps on and is

held in place by the screw holes.
Mount each bracket with an

attached shim at the previously

marked location.
Use a level to ensure that the brackets

are level and aligned.

■

■

■

«
...
18
19
20
21
22
...
»

Summary of Contents for Vertiglide Applause Honeycomb





















































Reviews:

No comments

Related manuals for Vertiglide Applause Honeycomb

Miza Desktop Rack Series

Brand: Zaor Pages: 3

Brand: Balmani Pages: 4

Brand: ofichairs Pages: 2

VLD 51/038-BSY+

Brand: D+H Pages: 20

Brand: MAJA Möbel Pages: 16

Brand: J&K Pages: 9

Brand: J D Williams Pages: 8

Brand: J&K Pages: 7

Monogram Beckett B14427

Brand: namesake Pages: 18

Brand: Cherryman Pages: 2

Brand: Habitat Pages: 11

Hampton Cabana 2102538

Brand: Backyard Discovery Pages: 47

ODYSSEA II EASY 2022R09P01-0273

Brand: Naterial Pages: 33

Brand: L.L.Bean Pages: 4

Brand: Baraboo Pages: 5

Brand: Hanover Pages: 5

Brand: panana Pages: 20

Active Day ACDK231L

Brand: Forte Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands