manualshive.com logo in svg

Hunter Type 2A Models, Owner'S Manual, Page: 10 / 14

Share
Download
Hunter Type 2A Models Owner'S Manual Download Page 10

10

42823-01  •  02/17/10  •  Hunter Fan Company

Your Hunter fan comes with an integrated light fixture assembly. 

 WARNING:

  Use only the light fixture supplied with this fan model.

7-1.  To attach the upper switch housing, partially install two housing 

assembly screws into the switch housing mounting plate.

7-2.  Feed the upper plug connector through the center opening of the 

housing. 

7-3.  Align the keyhole slots in the housing with the housing assembly 

screws. 

7-4.  Turn the housing counterclockwise until the housing assembly 

screws are firmly situated in the narrow end of the keyhole slots. 
Install the remaining screw into the housing. Tighten all three 
screws firmly.

     

 CAUTION:

  Make sure the upper switch housing is securely 

attached to the switch housing mounting plate. Failure to properly 
attach and tighten all three assembly screws could result in the 
switch housing and light fixture falling.

   

Steps 7-1 – 7-3

Housing 

Assembly 

Screw

Upper 

Switch 

Housing

7 • Completing Your Installation With a Bowl Light Fixture

Summary of Contents for Type 2A Models















Reviews:

No comments