background image

6

1886

1886

Need a little more help* with wiring?

Visit our wiring video at: 

http://bit.ly/

WireYourFan

*Fan style and features shown may vary.

You have two options for wiring your fan.

You are going to need these:

4 Wire Nuts (these are in the   bag)

Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch 
setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician.

Have a single switch?

Follow these steps:

Have dual switches?

Follow these steps:

Have extra wiring?

Turn the wires upward and push them carefully back through 
the hanger bracket into the outlet box. Make sure that the 
wires are still attached to the wire nuts.

Hunter Pro Tip:

Hunter Pro Tip:

Here is how to connect the wires:

Push the bare metal ends of the wires together and slide a wire 
nut over them. Then, twist the wire nut clockwise until tight. 

Give it a gentle pull to make sure none of the wires are loose.

Wiring the Fan

Connect the white 
(grounded) wire 
from the ceiling 
to the white wire 
from the fan.

Connect the white 
(grounded) wire 
from the ceiling 
to the white wire 
from the fan.

Cap the blue wire from the 
fan. 

You will not need it 

for single switch wiring.

Connect the second ungrounded 
(light) wire from the ceiling to 
the blue wire from the fan.

Connect the black 
(ungrounded) wire from 
the ceiling to the black 
wire from the fan.

Connect the three 
grounding wires (green, 
green/yellow stripe, or 
bare copper) coming from 
the ceiling, downrod, and 
hanging bracket.

Connect the three 
grounding wires (green, 
green/yellow stripe, or 
bare copper) coming from 
the ceiling, downrod, and 
hanging bracket.

Connect the black 
(ungrounded) wire from 
the ceiling to the black 
wire from the fan.

Blue

Blue

Black

Black

Green/Yellow Stripe

Green/Yellow Stripe

White

White

Ungrounded

Ungrounded

Ung

rounded (light)

Grounded

Grounded

Grounding

Grounding

G

r

e

en

/Ye

l

low

 

Str

ipe

G

r

e

en

/Ye

l

low

 

Str

ipe

x4

bag

x4

bag

Wire Nut

Wire Nut

Ceiling Bracket

Hanging Fan

Wiring

Canopy

Blades

Light

Glass

Remote

Troubleshooting

Downrod

Summary of Contents for Pendleton Series














Reviews: