Hunter M0046-01 Instructions Manual Download Page 15

Page: 15 / 17

www.HunterFan.com

1.888.830.1326

Light Kit (continued)

CONGRATUL

ATIONS!

YOU’RE DONE!

See next page for fan
operation instructions.

Connect the appropriate pull

chain pendant to each of the

short chains coming from the

inial and inial cap. The fan

pull chain controls the speed:

from high to off. The light

pull chain controls the light

ixture: on and off.

Press the globe and globe keeper

lush against the metal plate. Thread

the light pull chain through the hole

in the center of the inial cap and

thread the fan pull chain through the

hole in the side of the cap. Finally,

thread only the light pull chain

through the hole in the inial and

screw the inial onto the threaded rod.

Install a bulb into each of the

sockets. When necessary, replace

with bulbs of the same wattage.

Light

Pull

Chain

Fan

Pull

Chain

Note:

Globe style and number of

lights may vary.

Finial

Cap

Globe

Keeper

Metal

Plate

Globe

Hunter Fan Company

Summary of Contents for M0046-01


















Search results

Summary of Contents for M0046-01

Reviews:

Related manuals for M0046-01

Brands by name

Popular brands

Hunter M0046-01, Instructions Manual

Search results

Summary of Contents for M0046-01

Reviews:

Related manuals for M0046-01

Brands by name

Popular brands