Hunter 7 Models Owner'S Manual And Installation Manual Download

Page: 12 / 14

42768-01 • 02/23/09 • Hunter Fan Company

Installing the Glass Bowl

7-15. First install B10 candelabra bulbs (40 Watt

Maximum) into the sockets.

7-16. Place the glass bowl under the light fixture.

Make sure the pull chains fall through the
pull chain openings.

7-17. Place the cover plate up against the glass

bowl. Align the holes in the cover plate
and glass bowl.

7-18. Screw the finial onto the threaded rod end

until tight.

7-19. If you want the pull chains to be longer, use

the breakaway connectors to attach the
extra chains to the installed pull chains.

7 • Completing Your Installation With a Light Fixture (Continued)

Breakaway

Connector

Light Bulbs

(B10

Candelabra

Base 40 Watt

Maximum)

Glass Bowl

Cover Plate

Finial

Pull Chain

Openinig

Summary of Contents for 7 Models















Search results

Summary of Contents for 7 Models

Reviews:

Related manuals for 7 Models

Brands by name

Popular brands

Hunter 7 Models, Owner'S Manual And Installation Manual

Search results

Summary of Contents for 7 Models

Reviews:

Related manuals for 7 Models

Brands by name

Popular brands