manualshive.com logo in svg

Hunter 28111, Owner'S Manual

Share
Download
Hunter 28111 Owner'S Manual Download Page 11

11

41467-01  •  09/30/09  •  Hunter Fan Company

8-1.  To install the battery, remove the back cover of the remote. 

Insert the included 12-volt alkaline battery (Type 23A, MN-21 or 
equivalent) inside the remote, matching polarity on the battery 
as indicated by the + and - symbols in the battery compartment. 
Replace the cover.

    If you are using more than one remote controlled fan in the same 

area and want to control them separately, you must change the 
DIP switch settings in the remote before you install the battery. 
For instructions on setting the DIP switches, read the box on the 
next page.

8-2 .  To install the remote cradle on a switch plate,

 remove the two 

screws holding the switch cover plate. Do not remove the cover 
plate.

    Note:

 If you are installing the remote cradle on a rocker light 

switch, first break off the two tabs by pushing outward. 

    Orient the control cradle by lining up the two mounting holes 

with those on the switch. Insert and tighten the screws (do not 
over tighten).

8-3. 

To install the remote cradle on the wall,

 locate a 2 x 4 wall stud 

in a convenient location. Orient the remote cradle over the 2 x 4 
stud. Use 1” wood screws in either the inner or outer mounting 
holes.

    Wall anchors and 6-32 x 1” screws may be used in situations where 

mounting to a stud is not possible. Use the inner mounting holes.

 CAUTION:

 The remote control device complies with part 15 of the 

FCC rules. Changes or modifications not expressly approved by Hunter Fan 
Company could void your authority to operate this equipment.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference 

that may cause undesired operation.

Note:

 Use with a fan that incorporates an air gap switch (normal on-off wall 

switch). 

 WARNING:

 Maximum fan load is 100 Watts; maximum lamp is 300 Watts. 

Do not use any speed control with this product.

  Step 8-1

  Step 8-2

  Step 8-2 (Rocker Light Switch)

Removed 

Tabs

8 • Assembling the Remote Control and Mounting the Cradle

Summary of Contents for 28111















Reviews:

No comments

Brands by name

Popular brands

Load more brands