High Speed Impact-Release Transom Mount Transducer
7
531565-4_C
2. Drill the fourth mounting hole, using a 9/64" drill bit. Use a marine-
grade silicone sealant to fill all four drilled mounting holes, especially
if the holes penetrate the transom wall.
3. Re-position the transducer assembly against the transom of the boat,
then hand install the first three screws (two on the outside edges and
one in the 3rd mounting hole). Make sure that the transducer location
and the pivot angle have not changed, then fully tighten all three
mounting screws.
Hand tighten only!
4. Snap the pivot back down. Install the #8 x 1" wood screw into the 4th
hole to lock down the pivot arm.
Hand tighten only!
8.
Setting up the Transducer on the Control Head
Use the following instructions to set the transducer type in the control head.
When you select the transducer type, the related views and menus will be
added to the system.
Before you proceed, review the following information:
• If your transducer has the round connector, the instructions in this
section do not apply to your fishing system. The transducer will be set
up automatically on the control head. For troubleshooting or additional
information, download the Transducer Setup Guide from our Web site at
humminbird.com
, or see your control head operations manual.
• If your fishfinder is a PiranhaMAX, or does not include the Transducer
Select or Connected Transducer menu option, no further action is
required. The transducer will be detected automatically if it is
compatible with the control head. See your control head operations
manual for details.
1. Press the POWER/LIGHT key to power on the control head.
2. Press the MENU key. When the control head detects a functioning
transducer, it will automatically enter Normal operating mode. Follow the
on-screen prompts.
3.
Main Menu:
Press the MENU key twice.
4. Use the 4-WAY Cursor Control key to select the Sonar tab > Transducer
Select or Connected Transducer.
5. Press the RIGHT or LEFT Cursor keys to select the transducer type
(Dual Beam, Quad Beam, etc.). The available menu options will depend
on the transducer model you have attached.
6.
Close:
Press the EXIT key until the menu system is closed. Your control
head is now ready for operation.
Maintenance
If your boat remains in the water for long periods of time, algae and other
marine growth can reduce the effectiveness of the transducer. Periodically
clean the face of the transducer with a mild, marine-safe and plastic-safe
soap or solution.
If your boat remains out of the water for a long period of time, it may take
some time to wet the transducer after it is returned to the water. Small air
bubbles can cling to the surface of the transducer and interfere with proper
operation. These bubbles will dissipate with time, or you may wipe the face
of the transducer with your fingers after the transducer is in the water.
1-Year Limited Warranty
We warrant the original retail purchaser that products made by Humminbird
have been manufactured free from defects in materials and workmanship. This
warranty is effective for one year from the date of original retail purchase.
Humminbird products found to be defective and covered by this warranty will
be repaired or replaced free of charge at Humminbird’s option and returned to
the customer freight prepaid. Humminbird’s sole responsibility under this
warranty is limited to the repair or replacement of a product that has been
deemed defective by Humminbird. Humminbird is not responsible for charges
connected with the removal of such product or reinstallation of replaced or
repaired parts.
This warranty does not apply to a product that has been:
• Improperly installed;
• Used in an installation other than that recommended in the product
installation and operation instructions;
• Damaged or has failed because of an accident or abnormal operation;
• Repaired or modified by entities other than Humminbird.
Please retain your original receipt as a proof of the purchase date. This will be
required for in-warranty service.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD AND WILL BE
THE CUSTOMER'S EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE
IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN
DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. IN NO
EVENT WILL HUMMINBIRD BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY RELATING TO THE PRODUCTS.
Some states do not allow limitations on an implied warranty, or the exclusion
of incidental or consequential damages, so the above exclusions may not apply
to you. You may also have other rights, which vary from state to state.
Humminbird Service Policy
Even though you'll probably never need to take advantage of our incredible
service policy, it's good to know that we back our products this confidently.
We do it because you deserve the best. We will make every effort to repair
your unit within three business days from the receipt of your unit at our
factory. This does not include shipping time to and from our factory. Units
received on Friday are typically shipped by the following Wednesday, units
received Monday are typically shipped by Thursday, etc.
All repair work is performed by factory-trained technicians to meet exacting
factory specifications. Factory-serviced units go through the same rigorous
testing and quality control inspections as new production units.
After the original warranty period, a standard flat rate service charge will be
assessed for each repair (physical damage and missing parts are not included).
Any repairs made after the original warranty will be warranted for an
additional 90 days after service has been performed by our factory technicians.
You can contact our Customer Service or visit our Web site to verify the flat
rate repair fee for your product (visit the Product Support section):
http://www.humminbird.com