manualshive.com logo in svg

Hughes DIRECWAY DW7000, User Manual, Page: 34 / 98

Share
Download
Hughes DIRECWAY DW7000 User Manual Download Page 34

Chapter 2 • System Control Center

 

20

1035978-0001  Revision A

Browsing optimization 

utility

DIRECWAY offers a browsing optimization utility called the 
LAN Client Configuration Utility (LCCU). The utility configures 
certain settings on Windows operating systems to improve your 
Internet browsing experience. Follow these steps to download 
and install the utility:

1. Open a web browser on a computer connected to the 

DW7000.

2. Navigate to the System Control Center.

Refer to Accessing the System Control Center on page 8 for 
instructions explaining how to access the System Control 
Center.

3. Click 

View Help Topics

 on the System Control Center home 

page or click 

Help

 in the left pane of the page.

4. Click 

Browsing Optimization Utility

 to access the 

Browsing Optimization Utility page shown in Figure 15.

5. Click Download.

Figure 15:  Downloading the browsing optimization utility

Summary of Contents for DIRECWAY DW7000



































































































Reviews:

No comments