manualshive.com logo in svg

Hughes DIRECWAY DW7000, User Manual

Share
Download
Hughes DIRECWAY DW7000 User Manual Download Page 29

Chapter 2 • System Control Center

 

1035978-0001  Revision A

15

•

Bad Key Frames

 - indicates the percentage of received frames 

that could not be decrypted successfully. All data received 
over the satellite is encrypted. A continuously increasing 
value indicates the DW7000 is not commissioned. Click on 
System Status and check the 

Commission Status

 field on the 

page that appears. If it indicates the DW7000 is not 
commissioned, contact customer support.

Transmission 
Information page

The Transmission Information page is shown in Figure 10.

•

Transmit Status

 - reports the status of the transmit data path. 

Clicking on the blue status message displays corresponding 
help information.

•

Number of Successful Transmissions

 - reports the number of 

successful transmissions (frames) to the satellite.

•

Number of Failed Transmissions

 - reports the number of 

frames that could not be sent. A continuously increasing 
value indicates a problem with transmitting. However, if a 
low non-increasing value is displayed and the system is 
functioning, there is no reason for concern. You do not need 
to troubleshoot or contact customer support.

•

Number of Packets submitted for transmission

 - indicates the 

total number of data packets transmitted.

Figure 10:  Transmission Information page

Summary of Contents for DIRECWAY DW7000



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands